腳位
經過幾次測試後，司徒發現SK17i的UART腳位位置如下：
這種耳機孔最適合用來改造，完全不需要切斷PCB走線
使用膠帶將原本PCB接觸點隔離
跳線
完美的Debug介面
Baudrate 115200bps
UART傳輸線
腳位
經過幾次測試後，司徒發現SK17i的UART腳位位置如下：
這種耳機孔最適合用來改造，完全不需要切斷PCB走線
使用膠帶將原本PCB接觸點隔離
跳線
完美的Debug介面
Baudrate 115200bps
VBus is low, SoftService is not asserted... HW_REVISION_NUMBER = 0x205720e1 SEMCSEC Secure Bootstrap "1241-3656 S1Boot MSM7230 CRH1099189_R9A028" (2011-05-16 12:32) Platform startup reason: PWRKEY BQ charger detected Detected memories on MSM8255-0 rev 2 ASIC: EBI0 CS0: Micron 256MB LPDDR2 (SR 0x51ff), IO Calibration Done EBI1 CS0: Micron 256MB LPDDR2 (SR 0x51ff), IO Calibration Done EBI2 CS0: Micron 1024MB NAND (0x2c 0xb3 0x00) OTP User segment locked OTP User segment locked TA @ 0x08100000 (8*128kB) Hardware Config: verification OK OTP User segment locked MSN=BX902NF2HU IMEI=35821904119198 Model=SK17i SW=1244-7088_4.0.2.A.0.62 Service Mode Config From TA (ver 1.0): KEYS:1 USB:ON SERVICEMODE:USB SERVICE_PIN:ENABLED Modem cold start No Service Mode detected. Configuring long press:800 plf_bootos MSM7x30/8x55 TCB_VerifyASAHISignature hashLength=[0x14] ASAHILength=[0x23f] TCB_VerifyASAHISignature: S1_VerifySignature OK Partition table contents: PartID Descr Attribs StartBlock NumBlocks UsedAs 0x00000001 S1Boot 0x00000022 0x00000000 0x00000001 0x00000002 TA 0x00000001 0x00000008 0x00000008 0x00000008 AppDSP 0x40000022 0x0000015c 0x0000006c aDSP image 0x00000006 ModemFS 0x40000001 0x000000f4 0x00000068 mARM-FS image 0x00000005 ModemSW 0x40000022 0x00000010 0x000000e4 mARM image 0x00000003 Linux 0x80000022 0x00000280 0x00000064 aARM image 0x00000004 AppsFS1 0x80000001 0x000002f4 0x00000c80 system image 0x00000010 AppLog 0x80000001 0x00000f74 0x00000030 appslog image 0x0000000f AppsFS3 0xc0000001 0x00000fa4 0x0000032c cache image 0x0000000b FOTA0 0x40000022 0x000001c8 0x0000005c 0x0000000c FOTA1 0x40000022 0x00000224 0x0000005c 0x00000009 AppsFS2 0x80000001 0x000012d0 0x00000d20 userdata image Fastboot emulation not selected ARM ELF image (0x0028), entry point @ 0x04700000 ARM ELF image (0x0028), entry point @ 0x03e00000 ARM ELF image (0x0028), entry point @ 0x00208000 plf_ta_cmd_params() Boot parameters found in config data Commandline:totalmem=0x200 startup=0x00000001 serialno=BX902NF2HU bt0.ieee_addr=84:00:d2:f1:6a:37 wifi0.eth_addr=84:00:d2:f7:3f:e1. Warmboot address calculated: 0x00200000 Longpress OK - starting up EBI0 MPU Partition 0 start:0x03e00000 end:0x04328530 EBI1 MPU Partition 0 start:0x04700000 end:0x0694a000 EBI1 MPU Partition 1 start:0x04500000 end:0x04700000 EBI1 MPU Partition 2 start:0x00080000 end:0x00100000 EBI1 MPU Partition 3 start:0x00000000 end:0x00080000 NAND MPU Partition 0 start:0x00000280 end:0x00001ff0 NAND MPU Partition 1 start:0x00000fa4 end:0x000012d0 AXIGE_MPU_PART0_START MS:0x0000007c LS:0x00000000 AXIGE_MPU_PART0_END MS:0x00000086 LS:0x00005000 AXIGS_MPU_PART0_START MS:0x0000008e LS:0x00000000 AXIGS_MPU_PART0_END MS:0x000000d2 LS:0x00009400 AXIGS_MPU_PART1_START MS:0x0000008a LS:0x00000000 AXIGS_MPU_PART1_END MS:0x0000008e LS:0x00000000 AXIGS_MPU_PART2_START MS:0x00000001 LS:0x00000000 AXIGS_MPU_PART2_END MS:0x00000002 LS:0x00000000 AXIGS_MPU_PART3_START MS:0x00000000 LS:0x00000000 AXIGS_MPU_PART3_END MS:0x00000001 LS:0x00000000 Epic Qualcomm failure workaround activated (that means firewalling SMEM) FPB3_MPU_PART_START START:0x2b200000 END:0x2b300000 NAND MPU ON according to partition table TCB_SetAlloc TCB_SetFree TCB_SetReAlloc Jumping to code @ 0x04700000, goodbye and thanks for all the fish... Uncompressing Linux........................................................................................................................................................................... [ 0.000000] Linux version 2.6.32.9-perf (SEMCUser@SEMCHost) (gcc version 4.4.3 (GCC) ) #1 PREEMPT Wed Oct 19 09:31:26 2011 [ 0.000000] CPU: ARMv7 Processor [511f00f2] revision 2 (ARMv7), cr=10c53c7f [ 0.000000] CPU: VIPT nonaliasing data cache, VIVT ASID tagged instruction cache [ 0.000000] Machine: mogami [ 0.000000] Partition (from atag) system -- Offset:2f4 Size:c80 [ 0.000000] Partition (from atag) appslog -- Offset:f74 Size:30 [ 0.000000] Partition (from atag) cache -- Offset:fa4 Size:32c [ 0.000000] Partition (from atag) userdata -- Offset:12d0 Size:d20 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 116736 [ 0.000000] Normal zone: 2556 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 114180 pages, LIFO batch:31 [ 0.000000] allocating 5242880 bytes at 80ee0000 (10e0000 physical) for sf pmem arena [ 0.000000] allocating 5242880 bytes at 813e0000 (15e0000 physical) for fb [ 0.000000] allocating 2097152 bytes at 818e0000 (1ae0000 physical) for KGSL [ 0.000000] allocating 25165824 bytes at 81ae0000 (1ce0000 physical) for adsp pmem arena [ 0.000000] setting 25165824 bytes at 81ae0000 (1ce0000 physical) for adsp cached pmem arena [ 0.000000] allocating 14680064 bytes at 87200000 (7400000 physical) for swiqi pmem arena [ 0.000000] allocating 52428800 bytes at 88000000 (8200000 physical) for camera pmem arena [ 0.000000] allocating 2097152 bytes at 8b200000 (b400000 physical) for audio pmem arena [ 0.000000] allocating 6291456 bytes at 8b500000 (b700000 physical) for kernel ebi1 pmem arena [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 114180 [ 0.000000] Kernel command line: console=ttyMSM2,115200n8 androidboot.hardware=semc totalmem=0x200 startup=0x00000001 serialno=BX902NF2HU bt0.ieee_addr=84:00:d2:f1:6a:37 wifi0.eth_addr=81 [ 0.000000] USB serial number: 42583930324E46324855 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 60MB 140MB 256MB = 456MB total [ 0.000000] Memory: 341888k/342264k available, 124680k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xd0000000 - 0xf0000000 ( 512 MB) [ 0.000000] lowmem : 0x80000000 - 0xcfe00000 (1278 MB) [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB) [ 0.000000] .init : 0x80008000 - 0x80035000 ( 180 kB) [ 0.000000] .text : 0x80035000 - 0x806ec000 (6876 kB) [ 0.000000] .data : 0x80710000 - 0x80779a40 ( 423 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:566 [ 0.000000] Console: colour dummy device 80x30 [ 0.000122] Calibrating delay loop... 511.18 BogoMIPS (lpj=2555904) [ 0.240417] Mount-cache hash table entries: 512 [ 0.240844] CPU: Testing write buffer coherency: ok [ 0.242980] NET: Registered protocol family 16 [ 0.243865] ------------[ cut here ]------------ [ 0.243896] WARNING: at /home/hudsonslave/root/workspace/offbuild_edream4.0.1-release_matrix/HUDSON_PRODUCT/mango/HUDSON_VARIANT/user/label/CM/kernel/arch/arm/mach-msm/socinfo.c:430 soci) [ 0.243927] Unknown SOC ID! [ 0.243927] Modules linked in: [ 0.243957] [<8003c6c4>] (unwind_backtrace+0x0/0x150) from [<800d357c>] (warn_slowpath_common+0x48/0x60) [ 0.243988] [<800d357c>] (warn_slowpath_common+0x48/0x60) from [<800d35cc>] (warn_slowpath_fmt+0x24/0x30) [ 0.244018] [<800d35cc>] (warn_slowpath_fmt+0x24/0x30) from [<8000f394>] (socinfo_init+0xb4/0x314) [ 0.244049] unwind: Unknown symbol address 8000f394 [ 0.244049] unwind: Index not found 8000f394 [ 0.244079] ---[ end trace 1b75b31a2719ed1c ]--- [ 0.244140] socinfo_init: Unknown format found [ 4.497070] Clock ownership [ 4.497070] GLBL : 07d82110 [ 4.497100] APPS : 00000000 00000000 00000000 [ 4.497100] ROW : 00000000 00000000 [ 4.497161] Disabled VREG "gp3" [ 4.497161] Disabled VREG "gp5" [ 4.497253] acpu_clock_init() [ 4.498077] ACPU running at 768000 KHz [ 4.499755] ram_console: got buffer at 4ffe0000, size 20000 [ 4.499786] ram_console: no valid data in buffer (sig = 0xff3ff5f7) [ 4.499908] console [ram-1] enabled [ 4.500701] snddev_poweramp_gpio_init [ 4.502960] aux_pcm_gpio_init [ 4.503601] Enabled VREG "gp13" at 3050 mV [ 4.504119] Enabled VREG "gp4" at 2600 mV [ 4.504577] Enabled VREG "gp6" at 2900 mV [ 4.505065] Enabled VREG "gp7" at 1800 mV [ 4.505157] Vibrator: enable voltage 2700(mV) [ 4.505615] Enabled VREG "gp7" at 1800 mV [ 4.506011] Enabled VREG "gp6" at 2850 mV [ 4.540130] pm8058_init: i2c_add_driver: rc = 0 [ 4.540740] pm8058_probe: PMIC revision: E3 [ 4.542327] pm8058_gpio_probe: gpiochip_add(): rc=0 [ 4.542694] pm8058_mpp_probe: gpiochip_add(): rc=0 [ 4.549041] bio: create slab <bio-0> at 0 [ 4.549896] SCSI subsystem initialized [ 4.550201] usbcore: registered new interface driver usbfs [ 4.550292] usbcore: registered new interface driver hub [ 4.550384] usbcore: registered new device driver usb [ 4.550506] msm_i2c_probe [ 4.550628] msm_i2c_probe: clk_ctl 35d, 100000 Hz [ 4.551300] msm_i2c_probe [ 4.551452] msm_i2c_probe: clk_ctl 35d, 100000 Hz [ 4.552337] Bluetooth: Core ver 2.15 [ 4.552429] NET: Registered protocol family 31 [ 4.552459] Bluetooth: HCI device and connection manager initialized [ 4.552459] Bluetooth: HCI socket layer initialized [ 4.552581] Switching to clocksource gp_timer [ 4.556671] NET: Registered protocol family 2 [ 4.556823] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 4.557128] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 4.557464] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 4.557617] TCP: Hash tables configured (established 16384 bind 16384) [ 4.557647] TCP reno registered [ 4.557769] NET: Registered protocol family 1 [ 4.558044] RPC: Registered udp transport module. [ 4.558044] RPC: Registered tcp transport module. [ 4.558074] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 4.558227] Trying to unpack rootfs image as initramfs... [ 4.615386] Freeing initrd memory: 892K [ 4.616455] smd probe [ 4.616485] smd_core_init() [ 4.616516] smd_core_init() done [ 4.616546] smd_alloc_loopback_channel: 'local_loopback' cid=100 [ 4.616760] last_amsslog: Log not present [ 4.617095] smd_alloc_channel() 'DS' cid=0 [ 4.617218] smd_alloc_channel() 'DIAG' cid=1 [ 4.617279] smd_alloc_channel() 'RPCCALL' cid=2 [ 4.617370] smd_alloc_channel() 'DATA1' cid=7 [ 4.617431] smd_alloc_channel() 'DATA2' cid=8 [ 4.617523] smd_alloc_channel() 'DATA3' cid=9 [ 4.617584] smd_alloc_channel() 'DATA4' cid=10 [ 4.617675] smd_alloc_channel() 'DATA5' cid=11 [ 4.617736] smd_alloc_channel() 'DATA6' cid=12 [ 4.617797] smd_alloc_channel() 'DATA7' cid=13 [ 4.617889] smd_alloc_channel() 'DATA8' cid=14 [ 4.617950] smd_alloc_channel() 'DATA9' cid=15 [ 4.618041] smd_alloc_channel() 'DATA11' cid=17 [ 4.618103] smd_alloc_channel() 'DATA12' cid=18 [ 4.618194] smd_alloc_channel() 'BRG_1' cid=28 [ 4.618286] smd_alloc_channel() 'DAL00' cid=38 [ 4.618347] smd_alloc_channel() 'BRG_0' cid=39 [ 4.618438] smd_alloc_channel() 'DATA5_CNTL' cid=40 [ 4.618499] smd_alloc_channel() 'DATA6_CNTL' cid=41 [ 4.618591] smd_alloc_channel() 'DATA7_CNTL' cid=42 [ 4.618652] smd_alloc_channel() 'DATA8_CNTL' cid=43 [ 4.618743] smd_alloc_channel() 'DATA9_CNTL' cid=44 [ 4.618835] smd_alloc_channel() 'DATA12_CNTL' cid=45 [ 4.618957] Notify: smsm init [ 4.621032] SMD Packet Port Driver Initialized. [ 4.621520] SMD: ch 2 0 -> 1 [ 4.621795] SMD: ch 2 1 -> 2 [ 4.621917] [afe.c:afe_init] AFE driver init [ 4.622985] [audpp.c:audpp_probe] Number of decoder supported 5 [ 4.622985] [audpp.c:audpp_probe] Number of concurrency supported 7 [ 4.623016] [audpp.c:audpp_probe] module_name:AUDPLAY4TASK [ 4.623016] [audpp.c:audpp_probe] queueid:17 [ 4.623016] [audpp.c:audpp_probe] decid:4 [ 4.623046] [audpp.c:audpp_probe] nr_codec_support:1 [ 4.623046] [audpp.c:audpp_probe] module_name:AUDPLAY3TASK [ 4.623077] [audpp.c:audpp_probe] queueid:16 [ 4.623077] [audpp.c:audpp_probe] decid:3 [ 4.623077] [audpp.c:audpp_probe] nr_codec_support:11 [ 4.623107] [audpp.c:audpp_probe] module_name:AUDPLAY2TASK [ 4.623107] [audpp.c:audpp_probe] queueid:15 [ 4.623107] [audpp.c:audpp_probe] decid:2 [ 4.623138] [audpp.c:audpp_probe] nr_codec_support:11 [ 4.623138] [audpp.c:audpp_probe] module_name:AUDPLAY1TASK [ 4.623168] [audpp.c:audpp_probe] queueid:14 [ 4.623168] [audpp.c:audpp_probe] decid:1 [ 4.623168] [audpp.c:audpp_probe] nr_codec_support:11 [ 4.623199] [audpp.c:audpp_probe] module_name:AUDPLAY0TASK [ 4.623199] [audpp.c:audpp_probe] queueid:13 [ 4.623199] [audpp.c:audpp_probe] decid:0 [ 4.623229] [audpp.c:audpp_probe] nr_codec_support:11 [ 4.623931] [snddev_ecodec.c:snddev_ecodec_init] snddev_ecodec_init [ 4.627502] SMD: ch 38 0 -> 1 [ 4.627563] SMD: ch 38 1 -> 2 [ 4.630249] rpcrouter: Server create rejected, version = 0, program = 3000001f [ 4.636413] [adsp.c:adsp_rtos_mtoa_cb] INIT_INFO Event [ 4.636505] [adsp.c:adsp_init] msm_adsp -- 0 [ 4.636810] [lpa.c:lpa_probe] lpa probe [ 4.637023] audio_mvs_init: [ 4.637420] input: cyttsp_key as /devices/virtual/input/input0 [ 4.637573] input: msm_pmic_pwr_key as /devices/virtual/input/input1 [ 4.638061] rmt_storage_init_ramfs: No RAMFS table in SMEM [ 4.638092] rs300000a7: probe of rs300000a7.65536 failed with error -2 [ 4.638183] semc_battery_data semc_battery_data: probe [ 4.638610] simple_remote_pf simple_remote_pf.0: Successfully registered [ 4.639587] ashmem: initialized [ 4.640747] yaffs: yaffs built Nov 29 2011 12:44:25 Installing. [ 4.640808] msgmni has been set to 670 [ 4.640930] audio_mvs_thread: [ 4.643707] alg: No test for stdrng (krng) [ 4.643768] io scheduler noop registered [ 4.643798] io scheduler deadline registered (default) [ 4.645629] Registered led device: lcd-backlight [ 4.645721] Registered led device: button-backlight [ 4.645812] Registered led device: keyboard-backlight [ 4.645904] Registered led device: red [ 4.645965] Registered led device: green [ 4.646026] Registered led device: blue [ 4.668487] msm_fb_probe: phy_Addr = 0x15e0000 virt = 0xd0800000 [ 4.668945] MDP HW Base phy_Address = 0xa3f00000 virt = 0xd0100000 [ 4.669097] mdp_clk: mdp_clk=192000000 [ 4.669128] mdp_hw_version: mdp_hw_revision=1 [ 4.671325] mdp4_fetch_cfg: dmap=47 vg=c7 [ 4.671813] mddi_clk init rate is 92160000 [ 4.671936] primary mddi base phy_addr = 0xad600000 virt = 0xd003c000 [ 4.682220] mddi_sony_lcd_init (ver:0x3) [0] [ 4.682220] msm_mddi_semc_mogami_display_init [ 4.682281] mddi_sony_lcd_probe [0] [ 4.682403] MDDI: SONY HVGA: This is not sony LCD [ 4.682739] Found display with module ID = 0x1, revision ID = 0x1, driver IC ID = 0x1, driver ID = 0x4 [ 4.683227] mdp4_display_intf_sel: 0xa [ 4.687011] FrameBuffer[0] 320x480 size=1359872 bytes is registered successfully! [ 4.822814] mdp4_overlay_pipe_alloc: pipe=80746178 ndx=1 [ 4.834899] mddi_hitachi_lcd_probe: Probe success! [ 4.835174] mddi_sii_hvga: Detected a non-Sii display [ 4.835845] [ 4.835845] msm_vidc_dec: Inside vid_dec_init() [ 4.836029] [ 4.836029] msm_vidc_dec: Inside vid_dec_vcd_init() [ 4.836090] [ 4.836090] msm_vidc_enc: Inside vid_enc_init() [ 4.836242] [ 4.836242] msm_vidc_enc: Inside vid_enc_vcd_init() [ 4.836273] [ 4.836273] err: Device config mismatch [ 4.841156] diagfwd initializing .. [ 4.841491] SMD: ch 1 0 -> 1 [ 4.841522] diag opened SMD port ; r = 0 [ 4.841613] diagchar initializing .. [ 4.841674] SMD: ch 1 1 -> 2 [ 4.841827] diagchar initialized [ 4.843048] msm_serial: detected port #2 [ 4.843139] msm_serial.2: ttyMSM2 at MMIO 0xacc00000 (irq = 71) is a MSM [ 4.843231] msm_serial: console setup on port #2 [ 5.909912] console [ttyMSM2] enabled [ 5.913787] msm_serial: driver initialized [ 5.917785] msm_serial_hs.0: ttyHS0 at MMIO 0xa3300000 (irq = 73) is a MSM HS UART [ 5.925628] msm_serial_hs module loaded [ 5.930755] brd: module loaded [ 5.933959] loop: module loaded [ 5.935241] pmem: Initializing pmem (user-space) as cached [ 5.940887] pmem: Initializing pmem_kernel_ebi1 (in-kernel) [ 5.946228] pmem: Initializing pmem_adsp (user-space) as non-cached [ 5.952972] pmem: Initializing pmem_adsp_cached (user-space) as cached [ 5.959503] pmem: Initializing pmem_swiqi (user-space) as cached [ 5.965148] pmem: Initializing pmem_camera (user-space) as cached [ 5.971313] pmem: Initializing pmem_audio (user-space) as non-cached [ 5.977722] pmic8058_nfc_probe: OK [ 5.983398] lm3561 0-0053: lm3561_probe: loaded [ 5.988128] adie_codec_register_codec_operations: codec type 0 [ 5.991973] SCSI Media Changer driver v0.25 [ 5.995574] msm_nand_probe: phys addr 0xa0200000 [ 5.999969] msm_nand_probe: Dual Nand Ctrl in ping-pong mode [ 6.005615] msm_nand_probe: dmac 0x7 [ 6.009185] msm_nand_probe: allocated dma buffer at ffc2c000, dma_addr 4fbfa000 [ 6.017028] status: c00020 [ 6.019134] nandid: 55d1b32c maker 2c device b3 [ 6.023681] ONFI probe : Found an ONFI compliant device MT29F8G16ADBDAH4 , [ 6.030792] Found a supported NAND device [ 6.034790] NAND Id : 0x55d1b32c [ 6.038055] Buswidth : 16 Bits [ 6.041198] Density : 1024 MByte [ 6.044494] Pagesize : 2048 Bytes [ 6.047790] Erasesize: 131072 Bytes [ 6.051269] Oobsize : 64 Bytes [ 6.054412] 2nd_bbm : 0 [ 6.056915] CFG0 Init : 0xa85408c0 [ 6.060455] CFG1 Init : 0x0012745a [ 6.064025] ECCBUFCFG : 0x00000203 [ 6.067596] Creating 4 MTD partitions on "msm_nand": [ 6.072540] 0x000005e80000-0x00001ee80000 : "system" [ 6.313049] 0x00001ee80000-0x00001f480000 : "appslog" [ 6.317138] 0x00001f480000-0x000025a00000 : "cache" [ 6.377471] 0x000025a00000-0x00003fe00000 : "userdata" [ 6.625396] spi_qsd spi_qsd.0: msm_spi_probe: DM mode not supported [ 6.626953] PPP generic driver version 2.4.2 [ 6.627258] PPP Deflate Compression module registered [ 6.627380] PPP BSD Compression module registered [ 6.628326] PPP MPPE Compression module registered [ 6.628417] NET: Registered protocol family 24 [ 6.628509] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled). [ 6.628692] CSLIP: code copyright 1989 Regents of the University of California. [ 6.629486] rmnet_init [ 6.633544] rmnet_init [ 6.636016] msm_otg_probe: rpc_connect(0) [ 6.637084] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.642517] msm_hsusb_rpc_connect: usb_ep already connected [ 6.648071] host driver registered w/ tranceiver [ 6.652770] usbcore: registered new interface driver usb_ehset_test [ 6.659393] peripheral driver registered w/ tranceiver [ 6.664245] android_probe pdata: 80724bc8 [ 6.668060] android_bind [ 6.670471] android_bind_config [ 6.673736] android_usb gadget: android_usb ready [ 6.678283] msm_hsusb msm_hsusb: registered gadget driver 'android_usb' [ 6.685028] f_serial init [ 6.687500] android_register_function modem [ 6.691650] android_register_function nmea [ 6.695739] f_adb init [ 6.698089] android_register_function adb [ 6.702056] f_mass_storage init [ 6.705200] android_register_function usb_mass_storage [ 6.710327] f_rndis init [ 6.713012] android_register_function rndis [ 6.717010] f_mtp init [ 6.719360] android_register_function mtp [ 6.723358] f_accessory init [ 6.726196] android_register_function accessory [ 6.730712] f_diag init [ 6.733154] android_register_function diag [ 6.737243] rndis_function_bind_config MAC: 02:0C:1E:0B:78:67 [ 6.742980] android_usb gadget: using random self ethernet address [ 6.749114] android_usb gadget: using random host ethernet address [ 6.755676] usb0: MAC 3a:21:21:d9:c7:10 [ 6.759094] usb0: HOST MAC 16:cf:87:89:74:c8 [ 6.763488] acc_bind_config [ 6.766387] mass_storage_bind_config [ 6.769927] fsg_probe pdata: 80724bec [ 6.773773] android_usb gadget: Number of LUNs=2 [ 6.777954] MTP:android mtp driver [ 6.781585] mtp gadget driver initialize - success [ 6.786132] adb_bind_config [ 6.789642] diag_function_add [ 6.792633] input: pm8058-keypad as /devices/i2c-6/6-0000/pm8058-keypad/input/input2 [ 6.800689] usbcore: registered new interface driver xpad [ 6.804992] xpad: X-Box pad driver [ 6.808898] input: cyttsp-spi as /devices/platform/spi_qsd.0/spi0.0/input/input3 [ 6.815856] cyttsp-spi spi0.0: cyttsp_core_init: Enable ESD check [ 6.821960] cyttsp_core_init: Successful. [ 6.825805] cyttsp-spi spi0.0: cyttsp_set_bl_mode: ... trying. [ 6.831573] cyttsp-spi spi0.0: cyttsp_reinit_hw: Reinit HW [ 6.837066] cyttsp_xres: 1 [ 6.882995] cyttsp-spi spi0.0: cyttsp_set_bl_mode: completed. [ 6.922882] cyttsp-spi spi0.0: appver 3022, appid 0203 [ 6.923004] cyttsp-spi spi0.0: cyttsp_exit_bl_mode: trying .... [ 6.923370] cyttsp-spi spi0.0: appver 3022, appid 0203 [ 7.392608] cyttsp-spi spi0.0: cyttsp_exit_bl_mode: success. [ 7.392730] cyttsp-spi spi0.0: cyttsp_set_sysinfo_mode: trying .... [ 7.452728] cyttsp-spi spi0.0: cyttsp_set_sysinfo_mode: mode entered. [ 7.483215] cyttsp-spi spi0.0: cyttsp_set_sysinfo_mode: SI2:tts_ver=0x1300 app_id=0x0203 app_ver=0x3022 c_id=0xC0C1C2 [ 7.483428] cyttsp-spi spi0.0: cyttsp_set_intrvl_registers: act_intrvl=0x11 tch_tmout=0xFF lp_intrvl=0x0A [ 7.512603] cyttsp-spi spi0.0: cyttsp_power_on: switch back to operational mode [ 7.512756] cyttsp-spi spi0.0: cyttsp_set_operational_mode: trying .... [ 7.572845] cyttsp-spi spi0.0: chg_status_work: Set charger mode to reg: 0x0 [ 7.602600] cyttsp-spi spi0.0: cyttsp_set_operational_mode: mode entered. [ 7.622802] cyttsp-spi spi0.0: cyttsp_power_on: Power state is ACTIVE [ 7.622924] cyttsp_spi_probe: Successful registration cyttsp-spi [ 7.623107] cyttsp_spi_init: Cypress TrueTouch(R) Standard Product SPI Touchscreen Driver (Built Nov 29 2011 @ 12:44:22) returned 0 [ 7.623504] GPIO Input Driver: Start gpio inputs for slider-mogami in interrupt mode [ 7.623870] input: slider-mogami as /devices/virtual/input/input4 [ 7.625854] Enabled VREG "wlan" at 2900 mV [ 7.631500] Disabled VREG "wlan" [ 7.636779] input: apds9702 as /devices/virtual/input/input5 [ 7.637237] apds9702_probe: device create ok. I2C address = 54 [ 7.637603] simple_remote simple_remote.0: **** Registering (headset) driver [ 7.653076] input: simple_remote as /devices/virtual/input/input6 [ 7.653686] input: simple_remote_appkey as /devices/virtual/input/input7 [ 7.654937] simple_remote simple_remote.0: ***** Successfully registered [ 7.673156] bma250: detected chip id 3, rev 0x31 [ 7.676544] input: bma250 as /devices/virtual/input/input8 [ 7.677215] RTC Registering with rs30000048 [ 7.678680] msmrtc_rpc_proc_result: RPC client reply for PROC=12 success [ 7.683990] RPC CALL -- TOD TIME UPDATE: ttick = 471426 [ 7.683990] stamp=32768, freq = 1953849708 [ 7.691802] msmrtc_rpc_proc_result: RPC client reply for PROC=17 success [ 7.698944] using rtc device, msm_rtc, for alarms [ 7.702972] msm_rtc: dev (254:0) [ 7.706359] rs30000048 rs30000048.262144: rtc core: registered msm_rtc as rtc0 [ 7.713714] msm_rtc_secure: dev (254:1) [ 7.717346] rs30000048 rs30000048.262144: rtc core: registered msm_rtc_secure as rtc1 [ 7.725250] i2c /dev entries driver [ 7.729370] AKM8975 compass driver: initialize [ 7.733978] input: compass as /devices/virtual/input/input9 [ 7.738922] AKM8975 successfully probed. [ 7.742614] Linux video capture interface: v2.00 [ 7.771240] msmrtc_tod_proc_result: 01/06/1980 00:00:12 (06) [ 7.771392] rs30000048 rs30000048.262144: setting system clock to 1980-01-06 00:00:12 UTC (315964812) [ 8.185577] msm_gemini_init gemini: success [ 8.664337] bq27520 0-0055: FW v5.7 (expect v5.7). Golden FW v0.46 [ 8.664733] power_supply bq27520: driver failed to report `voltage_now' property [ 8.665557] bq24185 0-006b: Found BQ24185, rev 0x01 [ 8.666381] bq24185 0-006b: *** Safety limit could not be set! [ 8.666381] Please check boot accessing charger (want 0x50, got 0xac) *** [ 8.667541] bq24185 0-006b: Not initialized by boot [ 8.668640] chargalg chargalg: Registering battery charging algorithm driver [ 8.669799] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com [ 8.671173] Bluetooth: HCI UART driver ver 2.2 [ 8.675598] Bluetooth: HCI H4 protocol initialized [ 8.680328] Bluetooth: HCILL protocol initialized [ 8.685028] Bluetooth: HCI_IBS protocol initialized [ 8.691375] mmc0: Qualcomm MSM SDCC at 0x00000000a3100000 irq 100,523 dma 8 [ 8.696838] mmc0: 8 bit data mode disabled [ 8.700897] mmc0: 4 bit data mode enabled [ 8.704895] mmc0: polling status mode disabled [ 8.709320] mmc0: MMC clock 144000 -> 49152000 Hz, PCLK 76800000 Hz [ 8.715576] mmc0: Slot eject status = 1 [ 8.719390] mmc0: Power save feature enable = 1 [ 8.723907] mmc0: DM non-cached buffer at ffc30000, dma_addr 0x4f0aa000 [ 8.730499] mmc0: DM cmd busaddr 0x4f0aa000, cmdptr busaddr 0x4f0aa300 [ 8.737731] cdcc_pm_gpio_config: uSD power on [ 8.741821] usbcore: registered new interface driver usbhid [ 8.746948] usbhid: v2.6:USB HID core driver [ 8.751556] logger: created 64K log 'log_main' [ 8.755737] logger: created 256K log 'log_events' [ 8.760375] logger: created 64K log 'log_radio' [ 8.764923] logger: created 64K log 'log_system' [ 8.769500] Advanced Linux Sound Architecture Driver Version 1.0.21. [ 8.776184] No device for DAI CODEC_DAI [ 8.779541] No device for DAI CPU_DAI [ 8.783538] msm_soc: create pcms [ 8.786590] asoc: CODEC_DAI <-> CPU_DAI mapping ok [ 8.791931] No device for DAI MVS_CODEC_DAI [ 8.795379] No device for DAI MVS_CPU_DAI [ 8.799743] asoc: MVS_CODEC_DAI <-> MVS_CPU_DAI mapping ok [ 8.804840] ALSA device list: [ 8.807769] #0: msm-audio (MSM-CARD) [ 8.811553] u32 classifier [ 8.814178] Actions configured [ 8.817657] Netfilter messages via NETLINK v0.30. [ 8.822387] nf_conntrack version 0.5.0 (5361 buckets, 21444 max) [ 8.828704] ctnetlink v0.93: registering with nfnetlink. [ 8.833709] xt_time: kernel timezone is -0000 [ 8.838165] ip_tables: (C) 2000-2006 Netfilter Core Team [ 8.843353] arp_tables: (C) 2002 David S. Miller [ 8.847900] TCP cubic registered [ 8.851318] NET: Registered protocol family 10 [ 8.855987] lo: Disabled Privacy Extensions [ 8.862030] Mobile IPv6 [ 8.862091] IPv6 over IPv4 tunneling driver [ 8.866760] sit0: Disabled Privacy Extensions [ 8.871154] ip6tnl0: Disabled Privacy Extensions [ 8.875366] NET: Registered protocol family 17 [ 8.879669] NET: Registered protocol family 15 [ 8.884094] Bluetooth: L2CAP ver 2.14 [ 8.887695] Bluetooth: L2CAP socket layer initialized [ 8.892761] Bluetooth: SCO (Voice Link) ver 0.6 [ 8.897247] Bluetooth: SCO socket layer initialized [ 8.902740] Bluetooth: RFCOMM TTY layer initialized [ 8.906982] Bluetooth: RFCOMM socket layer initialized [ 8.912109] Bluetooth: RFCOMM ver 1.11 [ 8.915863] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 8.921112] Bluetooth: BNEP filters: protocol multicast [ 8.926330] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 8.936889] clock_late_init() disabled 27 unused clocks [ 8.940002] [voice.c:voice_init] [ 8.944183] cdcc_pm_gpio_config: uSD power off [ 8.946624] [voice.c:voice_thread] voice_thread() start [ 8.950592] simple_remote_pf simple_remote_pf.0: simple_remote_pf_button_handler - Button callback not re�[ 9.078430] power_supply bq27520: driver failed to report `voltage_now' propey [ 9.088592] yaffs: dev is 32505858 name is "mtdblock2" rw [ 9.088684] yaffs: passed flags "" [ 9.088745] yaffs: yaffs: Attempting MTD mount of 31.2,"mtdblock2" [ 9.132873] msm_otg_suspend: usb in low power mode [ 9.253204] bq27520 0-0055: IT Enable confirmed to be set. [ 9.273376] bq27520 0-0055: Writing BAT_INSERT [ 9.281738] yaffs: yaffs_read_super: is_checkpointed 0 [ 9.333496] yaffs: dev is 32505856 name is "mtdblock0" rw [ 9.333587] yaffs: passed flags "" [ 9.333648] yaffs: yaffs: Attempting MTD mount of 31.0,"mtdblock0" [ 9.522094] yaffs: yaffs_read_super: is_checkpointed 1 [ 9.564300] init: cannot: Master reset starting Sun Jan 6 00:00:15 1980[ 9.567535] yaffs: dev is 32505858 name is "mtdblock2" rw [ 9.567626] yaffs: passed flags "" [ 9.567687] yaffs: yaffs: Attempting MTD mount of 31.2,"mtdblock2" [ 9.569793] yaffs: yaffs_read_super: is_checkpointed 1 MR: Mounting /cache ourselves MR: Unmounting /cache [ 11.296875] bq27520 0-0055: bq27520_battery_info_setting() type=3 temp=250 status=0 [ 12.306762] bq27520 0-0055: bq27520_init_worker(): capacity=42 flags=0x139 [ 12.647796] yaffs: dev is 32505856 name is "mtdblock0" rw [ 12.647918] yaffs: passed flags "" [ 12.647979] yaffs: yaffs: Attempting MTD mount of 31.0,"mtdblock0" [ 12.836883] yaffs: yaffs_read_super: is_checkpointed 1 [ 12.853088] yaffs: dev is 32505859 name is "mtdblock3" rw [ 12.853179] yaffs: passed flags "" [ 12.853240] yaffs: yaffs: Attempting MTD mount of 31.3,"mtdblock3" [ 14.101562] yaffs: yaffs_read_super: is_checkpointed 0 [ 14.101776] yaffs: dev is 32505858 name is "mtdblock2" rw [ 14.101867] yaffs: passed flags "" [ 14.101928] yaffs: yaffs: Attempting MTD mount of 31.2,"mtdblock2" [ 14.104522] yaffs: yaffs_read_super: is_checkpointed 1 [ 14.121948] yaffs: dev is 32505857 name is "mtdblock1" rw [ 14.122070] yaffs: passed flags "" [ 14.122131] yaffs: yaffs: Attempting MTD mount of 31.1,"mtdblock1" [ 14.162475] yaffs: yaffs_read_super: is_checkpointed 0 [ 14.479400] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery' [ 14.485717] init: cannot find '/system/bin/hdmid', disabling 'hdmid' [ 14.517852] cyttsp-spi spi0.0: chg_status_work: Set charger mode to reg: 0x0 [ 14.524810] init: cannot find '/system/bin/dfdump', disabling 'dfdump'