RK3328

UART


參考資訊:
1. debug.html

腳位如下:


Baudrate 1500000bps

DDR version 1.13 20180428
ID:0x805 N
In
SRX
DDR4
333MHz
Bus Width=32 Col=10 Bank=4 Bank Group=2 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
ddrconfig:14
OUT
Boot1 Release Time: Sep  7 2018 15:49:55, version: 2.49
ChipType = 0x11, 272
mmc2:cmd19,100
SdmmcInit=2 0
BootCapSize=2000
UserCapSize=14910MB
FwPartOffset=2000 , 2000
SdmmcInit=0 NOT PRESENT
StorageInit ok = 19615
Raw SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit ret = 0, SecureMode = 0
GPT part:  0, name:            uboot, start:0x4000, size:0x2000
GPT part:  1, name:            trust, start:0x6000, size:0x2000
GPT part:  2, name:             boot, start:0xa000, size:0x10000
GPT part:  3, name:           backup, start:0x2a000, size:0x10000
GPT part:  4, name:           rootfs, start:0x5a000, size:0x1cc4fdf
find partition:uboot OK. first_lba:0x4000.
find partition:trust OK. first_lba:0x6000.
LoadTrust Addr:0x6000
No find bl30.bin
Load uboot, ReadLba = 4000
Load OK, addr=0x200000, size=0xce990
RunBL31 0x10000
INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-194-g646eecc5 #61 Wed Dec  5 06:31:51 UTC 2018 aarch64)

INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.4

INF [0x0] TEE-CORE:init_teecore:83: teecore inits done


U-Boot 2017.09-g0b1f585323 (Feb 02 2020 - 22:28:25 +0800)

Model: Firefly ROC-RK3328-CC
DRAM:  992 MiB
Relocation Offset is: 3dbf5000
Sysmem: init
Using default environment

rksdmmc@ff500000: 1, rksdmmc@ff520000: 0
Card did not respond to voltage select!
mmc_init: -95, time 9
GPT: my_lba incorrect: 281D00804B530000 != 1d1efff
GPT: my_lba incorrect: 281D00804B530000 != 1d1efff
Repair the backup gpt table OK!
Repair the backup gpt table OK!
switch to partitions #0, OK
mmc0(part 0) is current device
Bootdev: mmc 0
PartType: EFI
get part misc fail -1
boot mode: normal
Load FDT from boot part
DTB: rk-kernel.dtb
start get public phy
use default hdmi phy table
inno hdmi phy init success, save it
Warn: can't find connect driver
In:    serial
Out:   serial
Err:   serial
Model: Firefly ROC-RK3328-CC
Rockchip UBOOT DRM driver version: v1.0.1
use default hdmi phy table
xfer: num: 2, addr: 0x50
[dw_hdmi_i2c_read] read reg[0x01] data error:0x03
xfer: num: 2, addr: 0x50
[dw_hdmi_i2c_read] read reg[0x01] data error:0x03
xfer: num: 2, addr: 0x50
[dw_hdmi_i2c_read] read reg[0x01] data error:0x03
xfer: num: 2, addr: 0x50
[dw_hdmi_i2c_read] read reg[0x01] data error:0x03
xfer: num: 2, addr: 0x50
[dw_hdmi_i2c_read] read reg[0x01] data error:0x03
can't get edid block:0
failed to get edid
Could not find baseparameter partition
mode:1920x1080
CEA mode used vic=16
final pixclk = 148500000 tmdsclk = 148500000
start Inno HDMI PHY Power On
tmdsclock = 148500000; chipversion = 2
Inno HDMI PHY Power On
sink has audio support
hdmi_set_clk_regenerator: fs=48000Hz ftdms=148.500MHz N=6144 cts=148500
CLK: (sync kernel. arm: enter 600000 KHz, init 600000 KHz, kernel 0N/A)
  apll 400000 KHz
  dpll 664000 KHz
  cpll 1200000 KHz
  gpll 491009 KHz
  npll 600000 KHz
  armclk 600000 KHz
  aclk_bus 150000 KHz
  hclk_bus 75000 KHz
  pclk_bus 75000 KHz
  aclk_peri 150000 KHz
  hclk_peri 75000 KHz
  pclk_peri 75000 KHz
Net:   
Warning: ethernet@ff540000 (eth0) using random MAC address - f6:35:e3:87:88:7c
eth0: ethernet@ff540000
Hit key to stop autoboot('CTRL+C'):  0 
android_bootloader_boot_flow Could not find misc partition
ANDROID: reboot reason: "(none)"
Fdt Ramdisk skip relocation
FDT load addr 0x10f00000 size 200 KiB
Booting kernel at 0x00280000 with fdt at 0x8300000...


## Booting Android Image at 0x0027f800 ...
Kernel load addr 0x00280000 size 21343 KiB
## Flattened Device Tree blob at 08300000
   Booting using the fdt blob at 0x8300000
   XIP Kernel Image ... OK
   Using Device Tree in place at 0000000008300000, end 000000000831524d
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x0a200000 - 0x40000000 (size: 0x35e00000)
Can't find file:logo_kernel.bmp
Total: 4043.698 ms

Starting kernel ...


[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.4.167-g17982fadb9b5 (steward@debian) ((no: 17982fadb9b566ced754a05beb41dce220f58520) (gcc version 6.3.1 20170404 (Linaro GCC 60
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc03ff3e000 s46312 r8192 d31512 u86016
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: enabling workaround for ARM erratum 845719
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 249864
[    0.000000] Kernel command line: storagemedia=emmc androidboot.mode=emmc androidboot.slot_suffix= androidboot.serialno=1545fbe856b7cf18  rockchip_jtag rw 0
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    0.000000] software IO TLB [mem 0x3fd35000-0x3fd75000] (0MB) mapped at [ffffffc03fd35000-ffffffc03fd74fff]
[    0.000000] Memory: 972672K/1015808K available (13310K kernel code, 1822K rwdata, 5000K rodata, 1152K init, 2048K bss, 43136K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     modules : 0xffffff8000000000 - 0xffffff8008000000   (   128 MB)
[    0.000000]     vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000   (   246 GB)
[    0.000000]       .init : 0xffffff8009270000 - 0xffffff8009390000   (  1152 KB)
[    0.000000]       .text : 0xffffff8008080000 - 0xffffff8008d80000   ( 13312 KB)
[    0.000000]     .rodata : 0xffffff8008d80000 - 0xffffff8009270000   (  5056 KB)
[    0.000000]       .data : 0xffffff8009390000 - 0xffffff8009557808   (  1823 KB)
[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[    0.000000]               0xffffffbdc0008000 - 0xffffffbdc1000000   (    15 MB actual)
[    0.000000]     fixed   : 0xffffffbffe7fb000 - 0xffffffbffec00000   (  4116 KB)
[    0.000000]     PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000   (    16 MB)
[    0.000000]     memory  : 0xffffffc000200000 - 0xffffffc040000000   (  1022 MB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 64.
[    0.000000]  RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4
[    0.000000] NR_IRQS:64 nr_irqs:64 0
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001319] Console: colour dummy device 80x25
[    0.001354] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=24000)
[    0.001372] pid_max: default: 32768 minimum: 301
[    0.001485] Security Framework initialized
[    0.001576] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.001592] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    0.002597] Initializing cgroup subsys io
[    0.002628] Initializing cgroup subsys memory
[    0.002671] Initializing cgroup subsys devices
[    0.002696] Initializing cgroup subsys freezer
[    0.002715] Initializing cgroup subsys perf_event
[    0.002740] Initializing cgroup subsys net_prio
[    0.002760] Initializing cgroup subsys pids
[    0.002802] ftrace: allocating 48078 entries in 188 pages
[    0.141522] sched-energy: CPU device node has no sched-energy-costs
[    0.141553] Invalid sched_group_energy for CPU0
[    0.141563] CPU0: update cpu_capacity 1024
[    0.141640] ASID allocator initialised with 32768 entries
[    0.148436] Detected VIPT I-cache on CPU1
[    0.148518] Invalid sched_group_energy for CPU1
[    0.148524] CPU1: update cpu_capacity 1024
[    0.148530] CPU1: Booted secondary processor [410fd034]
[    0.149391] Detected VIPT I-cache on CPU2
[    0.149453] Invalid sched_group_energy for CPU2
[    0.149459] CPU2: update cpu_capacity 1024
[    0.149464] CPU2: Booted secondary processor [410fd034]
[    0.150305] Detected VIPT I-cache on CPU3
[    0.150361] Invalid sched_group_energy for CPU3
[    0.150366] CPU3: update cpu_capacity 1024
[    0.150371] CPU3: Booted secondary processor [410fd034]
[    0.150495] Brought up 4 CPUs
[    0.150560] SMP: Total of 4 processors activated.
[    0.150576] CPU features: kernel page table isolation forced OFF by command line option
[    0.150588] CPU features: detected feature: 32-bit EL0 Support
[    0.150603] CPU: All CPU(s) started at EL2
[    0.150651] alternatives: patching kernel code
[    0.150967] Invalid sched_group_energy for CPU3
[    0.150982] Invalid sched_group_energy for Cluster3
[    0.150991] Invalid sched_group_energy for CPU2
[    0.151001] Invalid sched_group_energy for Cluster2
[    0.151010] Invalid sched_group_energy for CPU1
[    0.151020] Invalid sched_group_energy for Cluster1
[    0.151029] Invalid sched_group_energy for CPU0
[    0.151039] Invalid sched_group_energy for Cluster0
[    0.152035] devtmpfs: initialized
[    0.178485] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.178530] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.179219] xor: measuring software checksum speed
[    0.188395]    8regs     :  1080.000 MB/sec
[    0.198478]    8regs_prefetch:   968.000 MB/sec
[    0.208562]    32regs    :  1456.000 MB/sec
[    0.218651]    32regs_prefetch:  1224.000 MB/sec
[    0.218662] xor: using function: 32regs (1456.000 MB/sec)
[    0.218703] pinctrl core: initialized pinctrl subsystem
[    0.220282] NET: Registered protocol family 16
[    0.226817] cpuidle: using governor ladder
[    0.230840] cpuidle: using governor menu
[    0.230886] Registered FIQ tty driver
[    0.231991] vdso: 2 pages (1 code @ ffffff8008d86000, 1 data @ ffffff8009394000)
[    0.232038] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.232265] DMA: preallocated 256 KiB pool for atomic allocations
[    0.261295] genirq: Setting trigger mode 8 for irq 177 failed (gic_set_type+0x0/0x64)
[    0.319241] console [ttyFIQ0] enabled
[    0.319976] Registered fiq debugger ttyFIQ0
[    0.388479] raid6: int64x1  gen()   199 MB/s
[    0.405521] raid6: int64x1  xor()   185 MB/s
[    0.422710] raid6: int64x2  gen()   324 MB/s
[    0.439886] raid6: int64x2  xor()   275 MB/s
[    0.457095] raid6: int64x4  gen()   480 MB/s
[    0.474211] raid6: int64x4  xor()   322 MB/s
[    0.491383] raid6: int64x8  gen()   394 MB/s
[    0.508580] raid6: int64x8  xor()   304 MB/s
[    0.525710] raid6: neonx1   gen()   359 MB/s
[    0.542946] raid6: neonx1   xor()   367 MB/s
[    0.560104] raid6: neonx2   gen()   562 MB/s
[    0.577266] raid6: neonx2   xor()   464 MB/s
[    0.594446] raid6: neonx4   gen()   753 MB/s
[    0.611631] raid6: neonx4   xor()   572 MB/s
[    0.628850] raid6: neonx8   gen()   769 MB/s
[    0.646047] raid6: neonx8   xor()   568 MB/s
[    0.646433] raid6: using algorithm neonx8 gen() 769 MB/s
[    0.646902] raid6: .... xor() 568 MB/s, rmw enabled
[    0.647351] raid6: using intx1 recovery algorithm
[    0.648342] mpp venc_srv: mpp_probe enter
[    0.648758] mpp venc_srv: init success
[    0.651427] vcc_sd: regulator get failed, ret=-517
[    0.652944] vcc_host_5v: supplied by vcc_sys
[    0.656378] iommu: Adding device ff350000.vpu_service to group 0
[    0.656999] iommu: Adding device ff351000.avsd to group 1
[    0.657592] iommu: Adding device ff360000.rkvdec to group 2
[    0.658177] iommu: Adding device ff330000.h265e to group 3
[    0.658786] iommu: Adding device ff340000.vepu to group 4
[    0.659354] iommu: Adding device ff370000.vop to group 5
[    0.660564] rk_iommu ff350800.iommu: can't get sclk
[    0.661543] rk_iommu ff360480.iommu: can't get aclk
[    0.661994] rk_iommu ff360480.iommu: can't get hclk
[    0.662474] rk_iommu ff360480.iommu: can't get sclk
[    0.663236] rk_iommu ff330200.iommu: can't get sclk
[    0.663966] rk_iommu ff340800.iommu: can't get sclk
[    0.664601] rk_iommu ff373f00.iommu: can't get sclk
[    0.665857] SCSI subsystem initialized
[    0.666951] usbcore: registered new interface driver usbfs
[    0.667551] usbcore: registered new interface driver hub
[    0.668167] usbcore: registered new device driver usb
[    0.668758] media: Linux media interface: v0.10
[    0.669222] Linux video capture interface: v2.00
[    0.669819] pps_core: LinuxPPS API ver. 1 registered
[    0.670268] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.671113] PTP clock support registered
[    0.673605] Advanced Linux Sound Architecture Driver Initialized.
[    0.675092] Bluetooth: Core ver 2.21
[    0.675500] NET: Registered protocol family 31
[    0.675904] Bluetooth: HCI device and connection manager initialized
[    0.676492] Bluetooth: HCI socket layer initialized
[    0.676938] Bluetooth: L2CAP socket layer initialized
[    0.677424] Bluetooth: SCO socket layer initialized
[    0.679285] rockchip-cpuinfo cpuinfo: Serial         : 1545fbe856b7cf18
[    0.681503] clocksource: Switched to clocksource arch_sys_counter
[    0.794724] NET: Registered protocol family 2
[    0.796036] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    0.796848] TCP bind hash table entries: 8192 (order: 6, 262144 bytes)
[    0.797836] TCP: Hash tables configured (established 8192 bind 8192)
[    0.798574] UDP hash table entries: 512 (order: 3, 49152 bytes)
[    0.799178] UDP-Lite hash table entries: 512 (order: 3, 49152 bytes)
[    0.800217] NET: Registered protocol family 1
[    0.801340] RPC: Registered named UNIX socket transport module.
[    0.801917] RPC: Registered udp transport module.
[    0.802343] RPC: Registered tcp transport module.
[    0.802795] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.806094] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[    0.811776] Initialise system trusted keyring
[    0.827929] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.829999] NFS: Registering the id_resolver key type
[    0.830537] Key type id_resolver registered
[    0.830919] Key type id_legacy registered
[    0.831709] fuse init (API version 7.23)
[    0.832784] SGI XFS with security attributes, no debug enabled
[    0.842137] NET: Registered protocol family 38
[    0.842617] Key type asymmetric registered
[    0.843000] Asymmetric key parser 'x509' registered
[    0.843857] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    0.844819] io scheduler noop registered
[    0.845192] io scheduler deadline registered
[    0.845678] io scheduler cfq registered (default)
[    0.849551] phy phy-ff450000.syscon:usb2-phy@100.1: Failed to get VBUS supply regulator
[    0.851756] rockchip-u3phy ff470000.usb3-phy: Failed to get VBUS supply regulator
[    0.855224] rockchip-u3phy ff470000.usb3-phy: Rockchip u3phy initialized successfully
[    0.857089] inno-hdmi-phy ff430000.hdmiphy: phy had been powered up
[    0.861884] rk-vcodec vpu_combo: no regulator for vcodec
[    0.862736] rk-vcodec vpu_combo: failed on clk_get clk_cabac
[    0.863255] rk-vcodec vpu_combo: failed on clk_get clk_core
[    0.863902] platform ff350000.vpu_service: probe device
[    0.864838] platform ff350000.vpu_service: drm allocator with mmu enabled
[    0.866685] platform ff351000.avsd: probe device
[    0.867736] platform ff351000.avsd: drm allocator with mmu enabled
[    0.870703] rk-vcodec vpu_combo: could not find power_model node
[    0.871260] rk-vcodec vpu_combo: init success
[    0.872123] rk-vcodec ff360000.rkvdec: no regulator for vcodec
[    0.872732] rk-vcodec ff360000.rkvdec: parent devfreq retry
[    0.874243] probe device ff330000.h265e
[    0.875097] mpp_dev ff330000.h265e: try to get iommu dev ffffffc03e615410
[    0.876281] mpp_dev ff330000.h265e: resource ready, register device
[    0.877442] probe device ff340000.vepu
[    0.878244] mpp_dev ff340000.vepu: try to get iommu dev ffffffc03e615c10
[    0.879314] mpp_dev ff340000.vepu: resource ready, register device
[    0.883464] dma-pl330 ff1f0000.dmac: Loaded driver for PL330 DMAC-241330
[    0.884099] dma-pl330 ff1f0000.dmac:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[    0.886992] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled
[    0.888653] ff120000.serial: ttyS1 at MMIO 0xff120000 (irq = 12, base_baud = 1500000) is a 16550A
[    0.891531] [drm] Initialized drm 1.1.0 20060810
[    0.896674] [drm] Rockchip DRM driver version: v1.0.1
[    0.897434] rockchip-drm display-subsystem: devfreq is not set
[    0.898472] rockchip-vop ff370000.vop: failed to get vop register byname
[    0.899152] rockchip-vop ff370000.vop: missing rockchip,grf property
[    0.900052] rockchip-drm display-subsystem: bound ff370000.vop (ops 0xffffff8008e3ce68)
[    0.901226] i2c i2c-4: of_i2c: modalias failure on /hdmi@ff3c0000/ports
[    0.901849] dwhdmi-rockchip ff3c0000.hdmi: registered DesignWare HDMI I2C bus driver
[    0.902688] dwhdmi-rockchip ff3c0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (inno_dw_hdmi_phy2)
[    0.905016] rockchip-drm display-subsystem: bound ff3c0000.hdmi (ops 0xffffff8008e31c58)
[    0.905773] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    0.906357] [drm] No driver support for vblank timestamp query.
[    0.908744] dwhdmi-rockchip ff3c0000.hdmi: failed to get edid
[    0.909827] get_framebuffer_by_node: failed to get logo,offset
[    0.960031] dwhdmi-rockchip ff3c0000.hdmi: failed to get edid
[    0.992151] rockchip-vop ff370000.vop: [drm:vop_crtc_enable] Update mode to 1280x720p60, type: 11
[    1.026240] Freeing drm_logo memory: 616K
[    1.066255] Console: switching to colour frame buffer device 160x45
[    1.101288] rockchip-drm display-subsystem: fb0:  frame buffer device
[    1.113184] Unable to detect cache hierarchy for CPU 0
[    1.115347] brd: module loaded
[    1.126959] loop: module loaded
[    1.128525] zram: Added device: zram0
[    1.129385] lkdtm: No crash points registered, enable through debugfs
[    1.132675] register spi return v = :0
[    1.135881] force_sf_dma_mode is ignored if force_thresh_dma_mode is set.
[    1.136713] rk_gmac-dwmac ff540000.ethernet: clock input or output? (input).
[    1.137348] rk_gmac-dwmac ff540000.ethernet: TX delay(0x28).
[    1.137880] rk_gmac-dwmac ff540000.ethernet: RX delay(0x16).
[    1.138398] rk_gmac-dwmac ff540000.ethernet: integrated PHY? (no).
[    1.139198] rk_gmac-dwmac ff540000.ethernet: cannot get clock clk_mac_speed
[    1.139835] rk_gmac-dwmac ff540000.ethernet: clock input from PHY
[    1.145395] rk_gmac-dwmac ff540000.ethernet: init for RGMII
[    1.146078] stmmac - user ID: 0x10, Synopsys ID: 0x35
[    1.146543]  Ring mode enabled
[    1.146823]  DMA HW capability register supported
[    1.147223]  Normal descriptors
[    1.147551]  RX Checksum Offload Engine supported (type 2)
[    1.148042]  Wake-Up On Lan supported
[    1.148444]  Enable RX Mitigation via HW Watchdog Timer
[    1.213918] libphy: stmmac: probed
[    1.214249] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[    1.214838] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[    1.217142] usbcore: registered new interface driver rtl8192cu
[    1.217779] usbcore: registered new interface driver rndis_wlan
[    1.218755] usbcore: registered new interface driver mt7601u
[    1.219381] Rockchip WiFi SYS interface (V1.00) ... 
[    1.220000] usbcore: registered new interface driver rtl8150
[    1.220616] usbcore: registered new interface driver r8152
[    1.221194] usbcore: registered new interface driver asix
[    1.221759] usbcore: registered new interface driver ax88179_178a
[    1.222362] usbcore: registered new interface driver cdc_ether
[    1.222959] usbcore: registered new interface driver rndis_host
[    1.223623] usbcore: registered new interface driver cdc_ncm
[    1.224194] usbcore: registered new interface driver qmi_wwan
[    1.224792] usbcore: registered new interface driver cdc_mbim
[    1.227973] phy phy-ff470000.usb3-phy.2: u3phy u2 power on
[    1.228532] phy phy-ff470000.usb3-phy.3: u3phy u3 power on
[    1.230562] ff580000.usb supply vusb_d not found, using dummy regulator
[    1.231266] ff580000.usb supply vusb_a not found, using dummy regulator
[    1.244682] dwc2 ff580000.usb: DWC OTG Controller
[    1.245162] dwc2 ff580000.usb: new USB bus registered, assigned bus number 1
[    1.245873] dwc2 ff580000.usb: irq 41, io mem 0xff580000
[    1.246691] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.247303] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.247964] usb usb1: Product: DWC OTG Controller
[    1.248394] usb usb1: Manufacturer: Linux 4.4.167-g17982fadb9b5 dwc2_hsotg
[    1.249028] usb usb1: SerialNumber: ff580000.usb
[    1.250562] hub 1-0:1.0: USB hub found
[    1.250952] hub 1-0:1.0: 1 port detected
[    1.252965] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.253608] ehci-pci: EHCI PCI platform driver
[    1.254137] ehci-platform: EHCI generic platform driver
[    1.257461] ehci-platform ff5c0000.usb: EHCI Host Controller
[    1.258382] ehci-platform ff5c0000.usb: new USB bus registered, assigned bus number 2
[    1.259344] ehci-platform ff5c0000.usb: irq 42, io mem 0xff5c0000
[    1.265532] ehci-platform ff5c0000.usb: USB 2.0 started, EHCI 1.00
[    1.266418] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.267053] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.267714] usb usb2: Product: EHCI Host Controller
[    1.268155] usb usb2: Manufacturer: Linux 4.4.167-g17982fadb9b5 ehci_hcd
[    1.268767] usb usb2: SerialNumber: ff5c0000.usb
[    1.270164] hub 2-0:1.0: USB hub found
[    1.270574] hub 2-0:1.0: 1 port detected
[    1.271817] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.272412] ohci-platform: OHCI generic platform driver
[    1.273622] ohci-platform ff5d0000.usb: Generic Platform OHCI controller
[    1.274644] ohci-platform ff5d0000.usb: new USB bus registered, assigned bus number 3
[    1.275572] ohci-platform ff5d0000.usb: irq 43, io mem 0xff5d0000
[    1.330822] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.331433] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.332095] usb usb3: Product: Generic Platform OHCI controller
[    1.332642] usb usb3: Manufacturer: Linux 4.4.167-g17982fadb9b5 ohci_hcd
[    1.333239] usb usb3: SerialNumber: ff5d0000.usb
[    1.334698] hub 3-0:1.0: USB hub found
[    1.335089] hub 3-0:1.0: 1 port detected
[    1.337105] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    1.338082] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 4
[    1.339083] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x04210010
[    1.339954] xhci-hcd xhci-hcd.9.auto: irq 181, io mem 0xff600000
[    1.340980] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[    1.341626] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.342268] usb usb4: Product: xHCI Host Controller
[    1.342766] usb usb4: Manufacturer: Linux 4.4.167-g17982fadb9b5 xhci-hcd
[    1.343364] usb usb4: SerialNumber: xhci-hcd.9.auto
[    1.344865] hub 4-0:1.0: USB hub found
[    1.345257] hub 4-0:1.0: 1 port detected
[    1.346233] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    1.347081] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    1.347959] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.348888] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003
[    1.349519] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.350162] usb usb5: Product: xHCI Host Controller
[    1.350619] usb usb5: Manufacturer: Linux 4.4.167-g17982fadb9b5 xhci-hcd
[    1.351216] usb usb5: SerialNumber: xhci-hcd.9.auto
[    1.352763] hub 5-0:1.0: USB hub found
[    1.353152] hub 5-0:1.0: 1 port detected
[    1.354373] usbcore: registered new interface driver cdc_acm
[    1.354912] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    1.355731] usbcore: registered new interface driver cdc_wdm
[    1.356326] usbcore: registered new interface driver uas
[    1.357061] usbcore: registered new interface driver usb-storage
[    1.357771] usbcore: registered new interface driver usbserial
[    1.358357] usbcore: registered new interface driver usbserial_generic
[    1.359008] usbserial: USB Serial support registered for generic
[    1.359677] usbcore: registered new interface driver ch341
[    1.360212] usbserial: USB Serial support registered for ch341-uart
[    1.360869] usbcore: registered new interface driver cp210x
[    1.361409] usbserial: USB Serial support registered for cp210x
[    1.362096] usbcore: registered new interface driver ftdi_sio
[    1.362686] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.363752] usbcore: registered new interface driver keyspan
[    1.364302] usbserial: USB Serial support registered for Keyspan - (without firmware)
[    1.365057] usbserial: USB Serial support registered for Keyspan 1 port adapter
[    1.365767] usbserial: USB Serial support registered for Keyspan 2 port adapter
[    1.366457] usbserial: USB Serial support registered for Keyspan 4 port adapter
[    1.367212] usbcore: registered new interface driver option
[    1.367811] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.369015] usbcore: registered new interface driver oti6858
[    1.369586] usbserial: USB Serial support registered for oti6858
[    1.370201] usbcore: registered new interface driver pl2303
[    1.370775] usbserial: USB Serial support registered for pl2303
[    1.371421] usbcore: registered new interface driver qcserial
[    1.372011] usbserial: USB Serial support registered for Qualcomm USB modem
[    1.372776] usbcore: registered new interface driver sierra
[    1.373330] usbserial: USB Serial support registered for Sierra USB modem
[    1.376090] usbcore: registered new interface driver usbtouchscreen
[    1.377252] .. rk pwm remotectl v1.1 init
[    1.378240] input: ff1b0030.pwm as /devices/platform/ff1b0030.pwm/input/input0
[    1.379872] sensor_register_slave:mma8452,id=17
[    1.380295] sensor_register_slave:lis3dh,id=7
[    1.380724] sensor_register_slave:mma7660,id=18
[    1.381137] sensor_register_slave:lsm303d,id=22
[    1.381569] sensor_register_slave:gs_mc3230,id=23
[    1.381993] [Gsensor]   gsensor_init
[    1.382328] sensor_register_slave:mpu6880_acc,id=24
[    1.382792] sensor_register_slave:mpu6500_acc,id=25
[    1.383239] sensor_register_slave:lsm330_acc,id=26
[    1.383690] sensor_register_slave:akm8975,id=30
[    1.384105] sensor_register_slave:akm8963,id=31
[    1.384534] sensor_register_slave:l3g4200d,id=45
[    1.384959] sensor_register_slave:l3g20d,id=46
[    1.385372] sensor_register_slave:ewtsa,id=47
[    1.385790] sensor_register_slave:lsm330_gyro,id=51
[    1.386240] sensor_register_slave:cm3217,id=53
[    1.386669] sensor_register_slave:cm3218,id=54
[    1.387952] i2c /dev entries driver
[    1.391764] rk808 1-0018: Pmic Chip id: 0x8050
[    1.393323] rk808 1-0018: source: on=0x40, off=0x00
[    1.410292] vcc_sd: supplied by vcc_io
[    1.417642] vdd_11: Bringing 1000000uV into 1100000-1100000uV
[    1.421692] rk808 1-0018: register rk8050 regulators
[    1.422671] rk8xx-gpio rk8xx-gpio: register rk8050 gpio successful
[    1.423586] rk8xx-pwrkey rk8xx-pwrkey: device is disabled
[    1.424084] rk8xx-pwrkey: probe of rk8xx-pwrkey failed with error -22
[    1.434664] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[    1.436124] rk808 1-0018: Can not read property pmic,hold-gpio
[    1.436689] rk808 1-0018: Can not read property pmic,stby-gpio
[    1.437261] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at ffffff80097f4000
[    1.439935] IR NEC protocol handler initialized
[    1.441433] usbcore: registered new interface driver uvcvideo
[    1.441981] USB Video Class driver (1.1.1)
[    1.448329] rockchip-thermal ff250000.tsadc: Missing tshut mode property, using default (cru)
[    1.449149] rockchip-thermal ff250000.tsadc: Missing tshut-polarity property, using default (low)
[    1.450354] rockchip-thermal ff250000.tsadc: tsadc is probed successfully!
[    1.452849] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[    1.454238] Bluetooth: Virtual HCI driver ver 1.5
[    1.455006] Bluetooth: HCI UART driver ver 2.3
[    1.455416] Bluetooth: HCI UART protocol H4 registered
[    1.455904] Bluetooth: HCI UART protocol LL registered
[    1.456365] Bluetooth: HCI UART protocol ATH3K registered
[    1.457016] usbcore: registered new interface driver bfusb
[    1.457640] usbcore: registered new interface driver btusb
[    1.458676] cpu cpu0: leakage=8
[    1.458984] cpu cpu0: leakage-volt-sel=0
[    1.459656] cpu cpu0: Failed to get pvtm
[    1.463588] sdhci: Secure Digital Host Controller Interface driver
[    1.464149] sdhci: Copyright(c) Pierre Ossman
[    1.464569] Synopsys Designware Multimedia Card Interface Driver
[    1.466815] dwmmc_rockchip ff500000.dwmmc: IDMAC supports 32-bit address mode.
[    1.467535] dwmmc_rockchip ff500000.dwmmc: Using internal DMA controller.
[    1.468156] dwmmc_rockchip ff500000.dwmmc: Version ID is 270a
[    1.468774] dwmmc_rockchip ff500000.dwmmc: DW MMC controller at irq 38,32 bit host data width,256 deep fifo
[    1.469688] dwmmc_rockchip ff500000.dwmmc: 'clock-freq-min-max' property was deprecated.
[    1.471388] rockchip-iodomain ff100000.syscon:io-domains: Setting to 3300000 done
[    1.472151] gpio-regulator: set GRF_SOC_CON10 bit 1 to 0
[    1.472645] enter gpio_regulator_set_voltage line 111 ,gpio=25 state=0
[    1.473238] rockchip-iodomain ff100000.syscon:io-domains: Setting to 3300000 done
[    1.484578] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.495671] dwmmc_rockchip ff500000.dwmmc: 1 slots initialized
[    1.497280] dwmmc_rockchip ff520000.dwmmc: IDMAC supports 32-bit address mode.
[    1.498078] dwmmc_rockchip ff520000.dwmmc: Using internal DMA controller.
[    1.498720] dwmmc_rockchip ff520000.dwmmc: Version ID is 270a
[    1.499314] dwmmc_rockchip ff520000.dwmmc: DW MMC controller at irq 39,32 bit host data width,256 deep fifo
[    1.512676] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[    1.524734] dwmmc_rockchip ff520000.dwmmc: 1 slots initialized
[    1.525586] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.528469] hidraw: raw HID events driver (C) Jiri Kosina
[    1.529820] usbcore: registered new interface driver usbhid
[    1.530318] usbhid: USB HID core driver
[    1.530960] inv_mpu_iio: inv_mpu_init:746
[    1.533998] rockchip-dmc dmc: unable to get devfreq-event device : dfi
[    1.539422] usbcore: registered new interface driver snd-usb-audio
[    1.541844] rk3328-codec ff410000.codec: rk3328 have no io-channels defined
[    1.542594] rk3328-codec ff410000.codec: spk_depop_time use default value.
[    1.550168] nf_conntrack version 0.5.0 (7603 buckets, 30412 max)
[    1.551670] IPVS: Registered protocols (TCP, UDP)
[    1.552175] IPVS: Connection hash table configured (size=4096, memory=64Kbytes)
[    1.553285] IPVS: Creating netns size=2104 id=0
[    1.553950] IPVS: ipvs loaded.
[    1.554244] IPVS: [rr] scheduler registered.
[    1.555018] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.555752] Initializing XFRM netlink socket
[    1.557285] NET: Registered protocol family 10
[    1.559341] NET: Registered protocol family 17
[    1.559846] NET: Registered protocol family 15
[    1.560302] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.561460] Bridge firewalling registered
[    1.561977] mmc1: MAN_BKOPS_EN bit is not set
[    1.562775] Bluetooth: RFCOMM socket layer initialized
[    1.563332] Bluetooth: RFCOMM ver 1.11
[    1.563750] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    1.564345] Bluetooth: HIDP socket layer initialized
[    1.564913] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    1.565843] [BT_RFKILL]: Enter rfkill_rk_init
[    1.566714] mmc_host mmc1: Bus speed (slot 0) = 150000000Hz (slot req 150000000Hz, actual 150000000HZ div = 0)
[    1.567666] Key type dns_resolver registered
[    1.568232] sensor_register_slave:mpu6880_gyro,id=50
[    1.569771] Registered cp15_barrier emulation handler
[    1.570228] Registered setend emulation handler
[    1.571762] Loading compiled-in X.509 certificates
[    1.575179] Btrfs loaded
[    1.576182] rga2: Module initialized.
[    1.576590] pvtm list NULL
[    1.577803] rk-vcodec ff360000.rkvdec: no regulator for vcodec
[    1.578372] rk-vcodec ff360000.rkvdec: parent devfreq retry
[    1.580342] rockchip-dmc dmc: current ATF version 0x101!
[    1.580844] rockchip-dmc dmc: read tf version 0x101!
[    1.583386] rockchip-dmc dmc: leakage=8
[    1.583757] rockchip-dmc dmc: leakage-volt-sel=0
[    1.584332] rockchip-dmc dmc: Failed to get pvtm
[    1.585522] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate
[    1.586095] rockchip-dmc dmc: failed to get vop pn to msch rl
[    1.592677] devfreq dmc: Couldn't update frequency transition information.
[    1.614652] asoc-simple-card sound: rk3328-hifi <-> ff010000.i2s mapping ok
[    1.617066] asoc-simple-card hdmi-sound: i2s-hifi <-> ff000000.i2s mapping ok
[    1.618636] rk-vcodec ff360000.rkvdec: no regulator for vcodec
[    1.619170] rk-vcodec ff360000.rkvdec: parent devfreq is ok
[    1.619995] rk-vcodec ff360000.rkvdec: probe device
[    1.620740] rk-vcodec ff360000.rkvdec: drm allocator with mmu enabled
[    1.621842] rk-vcodec ff360000.rkvdec: init success
[    1.622545] dhd_module_init: in Dongle Host Driver, version 1.579.77.41.10 (r)
[    1.622546] 
[    1.622551] =======================================================
[    1.622553] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
[    1.622554] =======================================================
[    1.622556] Realtek 8188EU USB WiFi driver (Powered by Rockchip,Ver v5.2.2.3_24783.20171030) init.
[    1.622560] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    1.622562] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
[    1.622563] RTW: module init start
[    1.622565] RTW: rtl8188eu v5.2.2.3_24783.20171030
[    1.622568] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[    1.622569] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: rfkill-wlan driver has not Successful initialized
[    1.622677] usbcore: registered new interface driver rtl8188eu
[    1.622679] RTW: module init ret=0
[    1.622885] ==gsl_ts_init==
[    1.622920] ret=0
[    1.624983] rk808-rtc rk808-rtc: setting system clock to 2016-01-21 08:51:11 UTC (1453366271)
[    1.631045] ======== dhd_wlan_init_plat_data ========
[    1.631508] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
[    1.632001] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: rfkill-wlan driver has not Successful initialized
[    1.632836] dhd_wlan_init_gpio: unknown oob irqflags !
[    1.633290] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=-1, oob_irq_flags=0x410
[    1.633949] dhd_wlan_init_gpio: WL_REG_ON=-1
[    1.634325] dhd_wifi_platform_load: Enter
[    1.634710] Power-up adapter 'DHD generic adapter'
[    1.635188] wifi_platform_set_power = 1
[    1.635528] vcc_sd: disabling
[    1.635534] vccio_sd: disabling
[    1.635564] ret 1024
[    1.635841] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of thi.
[    1.635988] mali-utgard ff300000.gpu: mali_platform_device->num_resources = 9
[    1.635993] mali-utgard ff300000.gpu: resource[0].start = 0x0x00000000ff300000
[    1.635997] mali-utgard ff300000.gpu: resource[1].start = 0x0x00000000ff300000
[    1.636002] mali-utgard ff300000.gpu: resource[2].start = 0x0x0000000000000012
[    1.636006] mali-utgard ff300000.gpu: resource[3].start = 0x0x0000000000000013
[    1.636010] mali-utgard ff300000.gpu: resource[4].start = 0x0x0000000000000014
[    1.636014] mali-utgard ff300000.gpu: resource[5].start = 0x0x0000000000000015
[    1.636018] mali-utgard ff300000.gpu: resource[6].start = 0x0x0000000000000016
[    1.636023] mali-utgard ff300000.gpu: resource[7].start = 0x0x0000000000000017
[    1.636027] mali-utgard ff300000.gpu: resource[8].start = 0x0x0000000000000018
[    1.636031] D : [File] : drivers/gpu/arm/mali400/mali/platform/rk/rk.c; [Line] : 623; [Func] : mali_platform_device_init(); to add platform_specific_data .
[    1.636207] mali-utgard ff300000.gpu: leakage=8
[    1.636215] mali-utgard ff300000.gpu: leakage-volt-sel=0
[    1.636284] mali-utgard ff300000.gpu: Failed to get pvtm
[    1.638137] Mali: Mali device driver loaded
[    1.639512] ALSA device list:
[    1.639515]   #0: rockchip,rk3328
[    1.639517]   #1: rockchip,hdmi
[    1.648424] ======== PULL WL_REG_ON(-1) HIGH! ========
[    1.648427] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    1.648432] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
[    1.650247] Waiting for root device PARTUUID=614e0000-0000...
[    1.664511] usb 4-1: new high-speed USB device number 2 using xhci-hcd
[    1.767540] devfreq ff300000.gpu: Couldn't update frequency transition information.
[    1.783443] usb 4-1: New USB device found, idVendor=05e3, idProduct=0727
[    1.784048] usb 4-1: New USB device strings: Mfr=3, Product=4, SerialNumber=2
[    1.784682] usb 4-1: Product: USB Storage
[    1.785035] usb 4-1: Manufacturer: Generic
[    1.785399] usb 4-1: SerialNumber: 000000000250
[    1.786881] usb-storage 4-1:1.0: USB Mass Storage device detected
[    1.787672] scsi host0: usb-storage 4-1:1.0
[    1.834567] usb 3-1: new full-speed USB device number 2 using ohci-platform
[    1.948553] wifi_platform_bus_enumerate device present 1
[    1.949034] ======== Card detection to detect SDIO card! ========
[    1.949610] sdio: host isn't  initialization successfully.
[    2.015992] usb 3-1: New USB device found, idVendor=1997, idProduct=2433
[    2.016652] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.017309] usb 3-1: Product: Mini Keyboard
[    2.017720] usb 3-1: Manufacturer:  
[    2.025822] input:   Mini Keyboard as /devices/platform/ff5d0000.usb/usb3/3-1/3-1:1.0/0003:1997:2433.0001/input/input1
[    2.050824] dwmmc_rockchip ff520000.dwmmc: Successfully tuned phase to 262
[    2.051585] mmc1: new HS200 MMC card at address 0001
[    2.053353] mmcblk1: mmc1:0001 AJTD4R 14.6 GiB 
[    2.054541] mmcblk1boot0: mmc1:0001 AJTD4R partition 1 4.00 MiB
[    2.055851] mmcblk1boot1: mmc1:0001 AJTD4R partition 2 4.00 MiB
[    2.057134] mmcblk1rpmb: mmc1:0001 AJTD4R partition 3 4.00 MiB
[    2.061725]  mmcblk1: p1 p2 p3 p4 p5
[    2.073276] vendor storage:20160801 ret = 0
[    2.079270] hid-generic 0003:1997:2433.0001: input,hidraw0: USB HID v1.01 Keyboard [  Mini Keyboard] on usb-ff5d0000.usb-1/input0
[    2.087630] input:   Mini Keyboard as /devices/platform/ff5d0000.usb/usb3/3-1/3-1:1.1/0003:1997:2433.0002/input/input2
[    2.140187] hid-generic 0003:1997:2433.0002: input,hidraw1: USB HID v1.01 Mouse [  Mini Keyboard] on usb-ff5d0000.usb-1/input1
[    2.160847] EXT4-fs (mmcblk1p5): mounted filesystem with ordered data mode. Opts: (null)
[    2.161665] VFS: Mounted root (ext4 filesystem) on device 179:5.
[    2.164885] devtmpfs: mounted
[    2.166134] Freeing unused kernel memory: 1152K
[    2.214840] EXT4-fs (mmcblk1p5): re-mounted. Opts: data=ordered
Starting logging: OK
Welcome to Rockchip Linux SDK
Populating /dev using udev: [    2.322474] udevd[175]: starting version 3.2.7
[    2.324301] random: udevd: uninitialized urandom read (16 bytes read, 26 bits of entropy available)
[    2.326109] random: udevd: uninitialized urandom read (16 bytes read, 26 bits of entropy available)
[    2.326992] random: udevd: uninitialized urandom read (16 bytes read, 26 bits of entropy available)
[    2.327887] random: udevd: uninitialized urandom read (16 bytes read, 26 bits of entropy available)
[    2.328779] random: udevd: uninitialized urandom read (16 bytes read, 26 bits of entropy available)
[    2.335088] udevd[175]: specified group 'kvm' unknown
[    2.353937] udevd[176]: starting eudev-3.2.7
[    2.434775] random: udevd: uninitialized urandom read (16 bytes read, 28 bits of entropy available)
[    2.438948] random: udevd: uninitialized urandom read (16 bytes read, 28 bits of entropy available)
done
Initializing random number generator... [    2.582281] random: dd: uninitialized urandom read (512 bytes read, 40 bits of entropy available)
done.
Will now mount all partitions in /etc/fstab
strings: /dev/block/by-name/misc: No such file or directory
Note: Create /.skip_fsck to skip fsck
 - The check might take a while if didn't shutdown properly!
Handling /dev/mmcblk1p5 / ext2 rw,noauto 1
Resizing /dev/mmcblk1p5(ext2)
[    2.718835] random: mktemp: uninitialized urandom read (10 bytes read, 41 bits of entropy available)
resize2fs 1.43.9 (8-Feb-2018)
[    2.729417] EXT4-fs (mmcblk1p5): resizing filesystem from 109939 to 3770875 blocks
[    2.792581] scsi 0:0:0:0: Direct-Access     Generic  STORAGE DEVICE   0250 PQ: 0 ANSI: 0
[    2.794972] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    2.801958] EXT4-fs (mmcblk1p5): resized filesystem to 3770875
Filesystem at /dev/mmcblk1p5 is mounted on /tmp/tmp.MbNd6wZmdm; on-line resizing required
old_desc_blocks = 1, new_desc_blocks = 1
The filesystem on /dev/mmcblk1p5 is now 3770875 (4k) blocks long.

tune2fs 1.43.9 (8-Feb-2018)
Checking /dev/mmcblk1p5(ext2)
[    2.879310] EXT4-fs (mmcblk1p5): re-mounted. Opts: data=ordered
e2fsck 1.43.9 (8-Feb-2018)
rootfs: clean, 6291/950272 files, 134986/3770875 blocks
[    2.921451] EXT4-fs (mmcblk1p5): re-mounted. Opts: data=ordered
[    2.928067] sd 0:0:0:0: [sda] 7744512 512-byte logical blocks: (3.97 GB/3.69 GiB)
[    2.929842] sd 0:0:0:0: [sda] Write Protect is off
[    2.931378] sd 0:0:0:0: [sda] No Caching mode page found
[    2.931913] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    2.943752]  sda: sda1
[    2.947321] sd 0:0:0:0: [sda] Attached SCSI removable disk
Log saved to /tmp/mountall.log
Starting system message bus: [    3.070088] random: dbus-uuidgen: uninitialized urandom read (12 bytes read, 87 bits of entropy available)
done
Starting network: [    3.134336] rk_gmac-dwmac ff540000.ethernet: rk_get_eth_addr: mac address: f6:35:e3:87:88:7c
[    3.135134] eth0: device MAC address f6:35:e3:87:88:7c
OK
Starting dhcpcd...
dev: loaded udev
DUID 00:01:00:01:1e:33:58:81:f6:35:e3:87:88:7c
eth0: IAID e3:87:88:7c
dummy0: waiting for carrier
dummy0: carrier acquired
dummy0: IAID ac:60:77:e8
dummy0: adding address fe80::c417:bb9c:35f6:ef54
eth0: soliciting a DHCP lease
[    3.347975] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[    3.356246] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
dummy0: soliciting a DHCP lease
eth0: soliciting an IPv6 router
[    3.949562] failed to power up DHD generic adapter, 1 retry left
[    3.966244] wifi_platform_set_power = 0
[    3.966639] ======== PULL WL_REG_ON(-1) LOW! ========
[    3.967097] [WLAN_RFKILL]: rockchip_wifi_power: 0
[    3.967557] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
[    3.968355] wifi_platform_bus_enumerate device present 0
[    3.968875] ======== Card detection to remove SDIO card! ========
[    3.969433] sdio: host isn't  initialization successfully.
[    3.970075] wifi_platform_set_power = 1
[    3.970430] ======== PULL WL_REG_ON(-1) HIGH! ========
[    3.970952] [WLAN_RFKILL]: rockchip_wifi_power: 1
[    3.971390] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
dummy0: soliciting an IPv6 router
[    4.272559] wifi_platform_bus_enumerate device present 1
[    4.273044] ======== Card detection to detect SDIO card! ========
[    4.273657] sdio: host isn't  initialization successfully.
eth0: carrier lost
[    5.342610] random: nonblocking pool is initialized
[    6.273603] failed to power up DHD generic adapter, 0 retry left
[    6.291331] wifi_platform_set_power = 0
[    6.291760] ======== PULL WL_REG_ON(-1) LOW! ========
[    6.292219] [WLAN_RFKILL]: rockchip_wifi_power: 0
[    6.292706] [WLAN_RFKILL]: rockchip_wifi_power: rfkill-wlan driver has not Successful initialized
[    6.293556] wifi_platform_bus_enumerate device present 0
[    6.294035] ======== Card detection to remove SDIO card! ========
[    6.294633] sdio: host isn't  initialization successfully.
[    6.295141] failed to power up DHD generic adapter, max retry reached**
[    6.295945] unregister wifi platform drivers
[    6.296337] wifi_platform_bus_enumerate device present 0
[    6.296878] ======== Card detection to remove SDIO card! ========
[    6.297424] sdio: host isn't  initialization successfully.
[    6.297953] ======== dhd_wlan_deinit_plat_data ========
[    6.298437] dhd_module_init: Failed to load the driver, try cnt 0
[    6.299164] dhd_module_init: Failed to load driver max retry reached**
[    6.299777] dhd_module_init: Exit err=-19
dummy0: no IPv6 Routers available
timed out
forked to background, child pid 472
Starting launcher: Date: 2016-01-21 UTC
[08:51:43.172] weston 3.0.0
               http://wayland.freedesktop.org
               Bug reports to: https://bugs.freedesktop.org/enter_bug.cgi?product=Wayland&component=weston&version=3.0.0
               Build: unknown (not built from git or tarball)
[08:51:43.175] Command line: weston --tty=2 --idle-time=0
[08:51:43.175] OS: Linux, 4.4.167-g17982fadb9b5, #1 SMP Sat Feb 1 14:21:07 CST 2020, aarch64
Info: <======= start audio service ========>
[08:51:43.190] Using config file '/etc/xdg/weston/weston.ini'
[08:51:43.192] Output repaint window is 15 ms maximum.
[08:51:43.193] Loading module '/usr/lib/libweston-3/drm-backend.so'
[08:51:43.208] initializing drm backend
[08:51:43.219] using /dev/dri/card0
[08:51:43.220] Loading module '/usr/lib/libweston-3/gl-renderer.so'
[08:51:43.234] EGL client extensions: EGL_EXT_client_extensions
               EGL_EXT_platform_base EGL_KHR_platform_gbm
               EGL_KHR_platform_wayland
arm_release_ver of this libMali is r7p0-00rel0, rk_so_ver is '1', built at '15:29:10', on 'Oct  8 2018'. 
[08:51:43.237] Unable to use first choice EGL config with id 0x34325241, succeeded with alternate id 0x34325258.
[08:51:43.238] warning: EGL_EXT_buffer_age not supported. Performance could be affected.
[08:51:43.239] EGL_KHR_surfaceless_context unavailable. Trying PbufferSurface
[08:51:43.242] EGL version: 1.4 Linux-r7p0-00rel0
[08:51:43.242] EGL vendor: ARM
[08:51:43.242] EGL client APIs: OpenGL_ES
[08:51:43.243] EGL extensions: EGL_KHR_image EGL_KHR_image_base
               EGL_KHR_image_pixmap EGL_EXT_image_dma_buf_import
               EGL_KHR_gl_texture_2D_image EGL_KHR_gl_texture_cubemap_image
               EGL_KHR_gl_renderbuffer_image EGL_KHR_reusable_sync
               EGL_KHR_fence_sync EGL_KHR_swap_buffers_with_damage
               EGL_EXT_swap_buffers_with_damage EGL_KHR_lock_surface
               EGL_KHR_lock_surface2 EGL_EXT_create_context_robustness
               EGL_ANDROID_blob_cache EGL_KHR_create_context
               EGL_WL_bind_wayland_display EGL_KHR_partial_update
               EGL_KHR_create_context_no_error
[08:51:43.248] GL version: OpenGL ES 2.0
[08:51:43.248] GLSL version: OpenGL ES GLSL ES 1.00
[08:51:43.248] GL vendor: ARM
[08:51:43.249] GL renderer: Mali-450 MP
[08:51:43.249] GL extensions: GL_OES_texture_npot GL_OES_vertex_array_object
               GL_OES_compressed_ETC1_RGB8_texture
               GL_EXT_compressed_ETC1_RGB8_sub_texture
               GL_OES_standard_derivatives GL_OES_EGL_image GL_OES_depth24
               GL_ARM_rgba8 GL_ARM_mali_shader_binary GL_OES_depth_texture
               GL_OES_packed_depth_stencil GL_EXT_texture_format_BGRA8888
               GL_OES_vertex_half_float GL_EXT_blend_minmax
               GL_OES_EGL_image_external GL_OES_EGL_sync GL_OES_rgb8_rgba8
               GL_EXT_multisampled_render_to_texture
               GL_EXT_discard_framebuffer GL_OES_get_program_binary
               GL_ARM_mali_program_binary GL_EXT_shader_texture_lod
               GL_EXT_robustness GL_OES_depth_texture_cube_map GL_KHR_debug
               GL_ARM_shader_framebuffer_fetch
               GL_ARM_shader_framebuffer_fetch_depth_stencil GL_OES_mapbuffer
               GL_KHR_no_error
[08:51:43.256] GL ES 2 renderer features:
               read-back format: RGBA
               wl_shm sub-image to texture: no
               EGL Wayland extension: yes
[08:51:43.260] event0  - [08:51:43.260] ff1b0030.pwm: [08:51:43.260] is tagged by udev as: Keyboard
[08:51:43.261] event0  - [08:51:43.261] ff1b0030.pwm: [08:51:43.261] device is a keyboard
[08:51:43.263] event1  - [08:51:43.263]   Mini Keyboard: [08:51:43.263] is tagged by udev as: Keyboard
[08:51:43.263] event1  - [08:51:43.263]   Mini Keyboard: [08:51:43.263] device is a keyboard
[08:51:43.265] event2  - [08:51:43.265]   Mini Keyboard: [08:51:43.265] is tagged by udev as: Keyboard Mouse
[08:51:43.265] event2  - [08:51:43.266]   Mini Keyboard: [08:51:43.266] device is a pointer
[08:51:43.266] event2  - [08:51:43.266]   Mini Keyboard: [08:51:43.266] device is a keyboard
[   33.446342] dwhdmi-rockchip ff3c0000.hdmi: failed to get edid
[   33.448185] dwhdmi-rockchip ff3c0000.hdmi: failed to get edid
[08:51:43.324] Registered plugin API 'weston_drm_output_api_v1' of size 24
[08:51:43.325] Unable to use first choice EGL config with id 0x34325241, succeeded with alternate id 0x34325258.
[08:51:43.325] Chosen EGL config details:
               RGBA bits: 8 8 8 8
               swap interval range: 0 - 10
[08:51:43.326] Failed to initialize backlight
[08:51:43.327] Output HDMI-A-1, (connector 69, crtc 64)
               mode 1280x720@60.0, preferred, current
               mode 1920x1080@60.0
               mode 1920x1080@50.0
               mode 1280x720@50.0
               mode 720x576@50.0
               mode 720x480@59.9
[08:51:43.329] Compositor capabilities:
               arbitrary surface rotation: yes
               screen capture uses y-flip: yes
               presentation clock: CLOCK_MONOTONIC, id 1
               presentation clock resolution: 0.000000001 s
[08:51:43.332] Loading module '/usr/lib/weston/desktop-shell.so'
[08:51:43.335] launching '/usr/libexec/weston-keyboard'
[08:51:43.337] launching '/usr/libexec/weston-desktop-shell'
Post Color Buffer Success
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
could not load cursor 'dnd-move'
could not load cursor 'dnd-copy'
could not load cursor 'dnd-none'
xkbcommon: ERROR: couldn't find a Compose file for locale "zh_CN.utf8"
could not create XKB compose table for locale 'zh_CN.utf8'.  Disabiling compose
xkbcommon: ERROR: couldn't find a Compose file for locale "zh_CN.utf8"
could not create XKB compose table for locale 'zh_CN.utf8'.  Disabiling compose
Starting pulseaudio: W: [pulseaudio] main.c: Running in system mode, but --disallow-exit not set.
W: [pulseaudio] main.c: Running in system mode, but --disallow-module-loading not set.
N: [pulseaudio] main.c: Running in system mode, forcibly disabling SHM mode.
N: [pulseaudio] main.c: Running in system mode, forcibly disabling exit idle time.
Using Wayland-EGL
arm_release_ver of this libMali is r7p0-00rel0, rk_so_ver is '1', built at '15:29:10', on 'Oct  8 2018'. 
MediaMonitor::listen()
------reuse !!accpet start----------
server is run.
MonitorThread run
Add inotify path: /mnt
Add inotify path: /mnt/sdcard
Add inotify path: /mnt/sdcard
qrc:/qml/qml/app_loading.qml:28:5: QML Text: Binding loop detected for property "font.pixelSize"
displayDpi may read wrong value,let's set to 160
displayDensity may read wrong value,let's set to 160
qml: background changed.
Using the 'xdg-shell-v6' shell integration
qml: updatePortraitMode:true
qml: background changed.
qml: updatePortraitMode:false
qml: updatePortraitMode:false
qml: updatePortraitMode:false
qml: updatePortraitMode:false
Post Color Buffer Success
OK
ssh-keygen: generating new host keys: RSA DSA ECDSA ED25519 
Starting sshd: OK
[   38.556104] file system registered
install_listener('tcp:5037','*smartsocket*')
[   38.577714] read descriptors
[   38.577987] read strings
sh: write error: No such device
wpa_supplicant.conf init
wpa_supplicant.conf init
load wifi modules: /etc/init.d/S66load_wifi_modules: line 42: rk_wifi_init: not found
FAIL
/etc/init.d/S66load_wifi_modules: line 42: wl: not found
Starting dnsmasq: OK
cat: /proc/device-tree/wireless-wlan/wifi_chip_type: No such file or directory
sh: rtl8723ds: unknown operand
Can't get device info: No such device
Can't get device info: No such device
Can't get device info: No such device
bluealsa: No HCI device available
Starting input-event-daemon: input-event-daemon: Start parsing /etc/input-event-daemon.conf...
input-event-daemon: Adding device: /dev/input/event0...
input-event-daemon: Adding device: /dev/input/event1...
input-event-daemon: Adding device: /dev/input/event2...
input-event-daemon: Start listening on 3 devices...
done
[root@rk3328:/]# bluealsa-aplay: ../src/shared/ctl-client.c:102: Connecting to socket: /var/run/bluealsa/hci0
bluealsa-aplay: BlueALSA connection failed: No such file or directory


返回上一頁