TRIMUI
焊接UART腳位
找一個空地
厚度剛好放下排針
跳線
背面(UART0)
完成
但是，UART竟然沒有任何輸出訊息
司徒一開始以為這個系統是RTOS相關客制系統，因此，好奇心驅使下，司徒更換到UART1測試一下
竟然有Bootloader訊息，這才發現，原來TRIMUI是使用UART1當作訊息輸出，真是天助我也！
[0]HELLO! BOOT0 is starting! [2]boot0 commit : 80628dcde5dc4ecdc757a9e782c58d7cf1abf959
重新焊接
背面
完成
Baudrate: 115200bps
[0]HELLO! BOOT0 is starting! [2]boot0 commit : 80628dcde5dc4ecdc757a9e782c58d7cf1abf959 [60]dram size =64 [62](GPIO_BASE_ADDR + 0x48): 0x00002222 [65](GPIO_BASE_ADDR + 0x5c): 0x00000055 [69](GPIO_BASE_ADDR + 0x64): 0x00000004 [72]CCMU_BASE_ADDR + 0x2c0 0x00104040 [76]CCMU_BASE_ADDR + 0x60 0x00104040 [79]SPIC0_BASE_ADDR+0x24: 0x00001004 [82]spinand UBOOT_START_BLK_NUM 8 UBOOT_LAST_BLK_NUM 58 [87]block from 8 to 58 [562]Check is correct. [573]Ready to disable icache. [575]Jump to secend Boot. U-Boot 2014.07 (Jul 26 2020 - 17:05:45) Allwinner Technology uboot commit : 8 i2c_init: by cpux [I2C-DEBUG]:i2c_set_clock() 354 [I2C-ERROR]:twi_send_clk_9pulse() 136 SDA is still Stuck Low, failed. i2c_init ok [0.620]pmbus: ready axp: get node[/soc/pmu0] error axp_probe error [0.627]PMU: cpux 696 Mhz,AXI=696 Mhz PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz key value = 4294967295, fel_key = [256,426] DRAM: 64 MiB Relocation Offset is: 03520000 axp: get node[/soc/pmu0] error int sunxi_dma_init--- irq enable workmode = 0,storage type = 0 [0.708]NAND: NAND_UbootInit [0.711]NAND_UbootInit start [0.713]NB1: enter NAND_LogicInit [0.718]nand0: get node offset error [0.721]init nctri NAND PIORequest error! [0.724]nand_physic_init, init nctri error [0.728]nand_physic_init init_parameter error [0.732]nand_physic_init error -1 [0.735]SpiNandHwInit: Start Nand Hardware initializing Nov 4 2018 13:15:18..... [0.742]uboot: nand version: 3 6019 20181104 1256 int sunxi_dma_init--- irq enable [0.757]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x83db8aa8 [0.765]uboot nand_request_tx_dma: reqest genernal dma for nand success, 0x83db8ac8 _change_spic_clk: 0x01c05024=0x1009 _change_spic_clk_v1: mclk=0xc8 _change_spic_clk: 0x01c05024=0x1004 _change_spic_clk_v1: mclk=0xc8 _change_spic_clk: 0x01c05024=0x1000 _change_spic_clk_v1: mclk=0xc8 _get_spic_clk_v1: sclk0=0x64 [0.808]not burn nand partition table! [0.812]NB1: nftl num: 1 [0.814]init nftl: 0 [1.022]NB1: NAND_LogicInit ok, result = 0x0 [1.026]NAND_UbootInit end: 0x0 used mbr [0], count = 8 logo addr = 0x83f00000 sunxi_read_bootlogo: read bootlogo partition successful do not find fastboot status flag --------fastboot partitions-------- -total partitions:8- -name- -start- -size- bootlogo : 400000 80000 env : 480000 40000 boot : 4c0000 480000 rootfs : 940000 7400000 rootfs_data : 7d40000 40000 misc : 7d80000 40000 private : 7dc0000 40000 UDISK : 7e00000 0 ----------------------------------- [1.132][NE]parameter error 32256,4 ! disable nand error: FDT_ERR_BADPATH disable nand error: FDT_ERR_BADPATH ## error: update_fdt_dram_para : FDT_ERR_NOTFOUND PowerBus = 0( 2:vBus 3:acBus other: not exist) no battery exist sunxi_bmp_logo_display Hit any key to stop autoboot: 0 ## Booting kernel from Legacy Image at 80007fc0 ... Image Name: ARM OpenWrt Linux-3.10.65 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3105608 Bytes = 3 MiB Load Address: 80008000 Entry Point: 80008000 XIP Kernel Image ... OK reserving fdt memory region: addr=81000000 size=10000 Using Device Tree in place at 81000000, end 8100f27f Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 3.10.65 (alfchen@alfchen-ubuntu) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #508 Sun Aug 30 16:04:27 UTC 2020 [ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: Allwinner A1X (Device Tree), model: sun3iw1p1 [ 0.000000] bootconsole [earlycon0] enabled [ 0.000000] cma: CMA: reserved 8 MiB at 83800000 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat c064065c, node_mem_map c067a000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: enforcing=1 earlyprintk=sunxi-uart,0x01c25000 initcall_debug=0 console=ttyS1,115200 loglevel=8 root=/dev/nandd init=/pseudo_init rdinit=/rdinit partition5 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 64MB = 64MB total [ 0.000000] Memory: 49980k/49980k available, 15556k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc4800000 - 0xff000000 ( 936 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc0528f84 (5252 kB) [ 0.000000] .init : 0xc0529000 - 0xc0548854 ( 127 kB) [ 0.000000] .data : 0xc054a000 - 0xc0640f88 ( 988 kB) [ 0.000000] .bss : 0xc0640f88 - 0xc0679a80 ( 227 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] of_sunxi_clocks_init : sunxi_clk_base[0xf1c20000] [ 0.000000] pll_cpu-set_default_rate=720000000 success! [ 0.000000] pll_video-set_default_rate=297000000 success! [ 0.000000] pll_ddr-set_default_rate=312000000 success! [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] Console: colour dummy device 80x30 [ 0.005246] Calibrating delay loop... 358.80 BogoMIPS (lpj=1794048) [ 0.065269] pid_max: default: 32768 minimum: 301 [ 0.070371] Mount-cache hash table entries: 512 [ 0.076215] CPU: Testing write buffer coherency: ok [ 0.081957] Setting up static identity map for 0xc03f6160 - 0xc03f61b8 [ 0.090948] devtmpfs: initialized [ 0.096268] pinctrl core: initialized pinctrl subsystem [ 0.103659] NET: Registered protocol family 16 [ 0.111161] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.118779] dump_class_init,844, success [ 0.126968] sun3iw1p1-pinctrl pio: initialized sunXi PIO driver [ 0.149483] bio: create slabat 0 [ 0.154801] pwm module init! [ 0.159328] SCSI subsystem initialized [ 0.163596] usbcore: registered new interface driver usbfs [ 0.169364] usbcore: registered new interface driver hub [ 0.175229] usbcore: registered new device driver usb [ 0.185868] sun3iw1p1-pinctrl pio: missing allwinner,pins property in node twi2 [ 0.193771] sun3iw1p1-pinctrl pio: missing allwinner,pins property in node twi2 [ 0.201295] twi_request_gpio()367 - TWI2 devm_pinctrl_get() failed! return -22 [ 0.208777] sunxi_i2c_hw_init()1004 - [i2c2] request i2c gpio failed! [ 0.215484] twi: probe of twi2 failed with error -5 [ 0.220767] Linux video capture interface: v2.00 [ 0.226105] Advanced Linux Sound Architecture Driver Initialized. [ 0.233822] cfg80211: Calling CRDA to update world regulatory domain [ 0.241228] Switching to clocksource sun3i high-res couter [ 0.263747] usb_script_parse [ 0.266843] port_type is 2 [ 0.271234] NET: Registered protocol family 2 [ 0.277604] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.284707] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.291355] TCP: Hash tables configured (established 512 bind 512) [ 0.297896] TCP: reno registered [ 0.301290] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.307383] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.314371] NET: Registered protocol family 1 [ 0.332395] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.338972] jffs2: version 2.2. �© 2001-2006 Red Hat, Inc. [ 0.345322] msgmni has been set to 113 [ 0.352384] io scheduler noop registered [ 0.356565] io scheduler cfq registered (default) [ 0.361534] [pm]aw_pm_init! [ 0.364789] [pm]valid [ 0.367262] [pm]valid [ 0.369958] [DISP]disp_module_init [ 0.427098] pll_freq=297000000HZ, lcd_dclk_freq=19000000HZ, clk_div=15 [ 0.434521] num_screens=1 [ 0.437368] screen_id=0 [ 0.439947] para->mclk[MOD_CLK_LCD1CH0]=0xc300c340 [ 0.444894] para->mclk[MOD_CLK_LCD1CH1]=0xc300c440 [ 0.449882] disp tv init [ 0.452549] tcon_clk=0xc300c340, tcon_clk_parent=0x0 [ 0.457713] tcon_clk=0xc300c340, tcon_clk_parent=0xc3004400 [ 0.463458] tve_clk=0xc300c440, tve_clk_parent=0xc3004400 [ 0.469053] disp al tv init [ 0.474387] fetch script datadisp.screen2_output_type fail [ 0.480428] fetch script datadisp.screen2_output_mode fail [ 0.486350] fb0_format 5 [ 0.491059] fetch script datadisp.fb2_format fail [ 0.496184] fetch script datadisp.fb2_scaler_mode_enable fail [ 0.502442] fetch script datadisp.fb2_width fail [ 0.507546] fetch script datadisp.fb2_height fail [ 0.520143] [DISP] disp_get_lcd,line:62: screen_id 1 out of range [ 0.526710] screen 0 lcd is c055565c or set_bright is nil [ 0.532382] [DISP]disp_module_init 1 finish [ 0.548302] uart1: ttyS1 at MMIO 0x1c25400 (irq = 104) is a SUNXI [ 0.554621] sw_console_setup()1324 - console setup baud 115200 parity n bits 8, flow n [ 0.562881] console [ttyS1] enabled, bootconsole disabled [ 0.562881] console [ttyS1] enabled, bootconsole disabled [ 0.575339] misc dump reg init [ 0.580610] [NAND]SPIC0_BASE_ADDR f1c05000 [ 0.585853] Failed to get dragonboard_flag [ 0.590510] [NAND]nand init start [ 0.594203] SpiNandHwInit: Start Nand Hardware initializing Nov 4 2018 05:15:38..... [ 0.602953] kernel: nand version: 3 6019 20181104 1256 [ 0.608702] print_level is no used [ 0.612486] request spi gpio ok! [ 0.616163] request tx DMA [ 0.619207] request general tx dma channel ok! [ 0.624142] request rx DMA [ 0.627192] request general rx dma channel ok! [ 0.632127] NAND_ClkRequest [ 0.635268] NAND_ClkRequest: get pll6 rate 200000000HZ [ 0.641101] SPI nand ID: 12c212c2 12c212c2 [ 0.645680] [SCAN_DBG] NandTwoPlaneOp: 1, DriverTwoPlaneOPCfg: 1, 0xffcfffff [ 0.653666] id_number_ctl is no used [ 0.657675] _UpdateExtAccessFreqPara: no para. [ 0.663172] PHY_Scan_DelayMode: right delay mode 0x0 [ 0.669165] PHY_Scan_DelayMode: right delay mode 0x800 [ 0.674930] _get_spic_clk_v1: sclk0=0x64 [ 0.679367] PHY_Scan_DelayMode: right delay mode,clk 100 MHz, SPI_TCR = 0x00000984, bit[13]=0,bit[11]=1 [ 0.689841] physic_info_read start!! [ 0.693837] physic_info_get_offset start!! [ 0.701767] physic_info_get_one_copy start!! [ 0.707390] block 13 page 48 [ 0.710963] block 13 page 49 [ 0.714533] block 13 page 50 [ 0.718179] block 13 page 51 [ 0.721743] block 13 page 52 [ 0.725315] block 13 page 53 [ 0.728964] block 13 page 54 [ 0.732532] block 13 page 55 [ 0.736098] block 13 page 56 [ 0.739746] block 13 page 57 [ 0.743315] block 13 page 58 [ 0.746884] block 13 page 59 [ 0.750532] block 13 page 60 [ 0.754110] block 13 page 61 [ 0.757755] block 13 page 62 [ 0.761329] block 13 page 63 [ 0.765517] physic info copy is ok [ 0.769395] [ 0.769395] [ 0.772699] [SCAN_DBG] ==============Nand Architecture Parameter============== [ 0.780763] [SCAN_DBG] Nand Chip ID: 0xffff12c2 0xffffffff [ 0.787951] [SCAN_DBG] Nand Chip Count: 0x1 [ 0.793366] [SCAN_DBG] Nand Chip Connect: 0x1 [ 0.798809] [SCAN_DBG] Sector Count Of Page: 0x4 [ 0.804224] [SCAN_DBG] Page Count Of Block: 0x40 [ 0.809762] [SCAN_DBG] Block Count Of Die: 0x400 [ 0.815370] [SCAN_DBG] Plane Count Of Die: 0x2 [ 0.820810] [SCAN_DBG] Die Count Of Chip: 0x1 [ 0.826225] [SCAN_DBG] Bank Count Of Chip: 0x1 [ 0.831665] [SCAN_DBG] Optional Operation: 0x6d [ 0.837200] [SCAN_DBG] Access Frequence: 0x64 [ 0.842710] [SCAN_DBG] ======================================================= [ 0.842710] [ 0.875114] secure storage updata ok! [ 0.879278] nand secure storage ok: 58,59 [ 0.883759] start block:60 [ 0.886772] [ND]boot start [ 0.889918] [ND]boot :0xc3140000 [ 0.893502] [ND]boot->magic :0xaa55a5a5 [ 0.897792] [ND]boot->len :0x8000 [ 0.901472] [ND]boot->no_use_block :0x21 [ 0.905824] [ND]boot->uboot_start_block :0x8 [ 0.910591] [ND]boot->uboot_next_block :0x3a [ 0.915330] [ND]boot->logic_start_block :0x21 [ 0.920193] [ND]mbr len :4096 [ 0.923486] [ND]_PARTITION len :2560 [ 0.927480] [ND]_NAND_STORAGE_INFO len :512 [ 0.932121] [ND]_FACTORY_BLOCK len :2048 [ 0.936553] [NE]partition_num: 0,size :0x36e00,cross_talk 0 [ 0.942789] [NE]part mbr size: 0x2000 type: 0 [ 0.947659] [NE]part bootlogo size: 0x400 type: 0 [ 0.952884] [NE]part env size: 0x200 type: 0 [ 0.957651] [NE]part boot size: 0x2400 type: 0 [ 0.962586] [NE]part rootfs size: 0x3a000 type: 0 [ 0.967836] [NE]part rootfs_data size: 0x200 type: 0 [ 0.973349] [NE]part misc size: 0x200 type: 0 [ 0.978213] [NE]part private size: 0x200 type: 0 [ 0.983340] [NE]part UDISK size: 0xffff7e00 type: 0 [ 0.988894] [ND]partition->size :224768 [ 0.993151] [ND]partition->cross_talk :0 [ 0.997541] [ND]partition->attribute :0 [ 1.001798] [ND]partition->start.Chip_NO :0 [ 1.006439] [ND]partition->start.Block_NO :33 [ 1.011306] [ND]partition->end.Chip_NO :0 [ 1.015757] [ND]partition->end.Block_NO :511 [ 1.020525] [ND]partition->nand_disk[0].size :8192 [ 1.025843] [ND]partition->nand_disk[0].type :0 [ 1.030897] [ND]partition->nand_disk[1].size :1024 [ 1.036216] [ND]partition->nand_disk[1].type :0 [ 1.041269] [ND]partition->nand_disk[2].size :512 [ 1.046490] [ND]partition->nand_disk[2].type :0 [ 1.051544] [ND]partition->nand_disk[3].size :9216 [ 1.056863] [ND]partition->nand_disk[3].type :0 [ 1.061917] [ND]partition->nand_disk[4].size :237568 [ 1.067453] [ND]partition->nand_disk[4].type :0 [ 1.072483] [ND]partition->nand_disk[5].size :512 [ 1.077728] [ND]partition->nand_disk[5].type :0 [ 1.082758] [ND]partition->nand_disk[6].size :512 [ 1.088005] [ND]partition->nand_disk[6].type :0 [ 1.093034] [ND]partition->nand_disk[7].size :512 [ 1.098280] [ND]partition->nand_disk[7].type :0 [ 1.103309] [ND]partition->nand_disk[8].size :-33280 [ 1.108846] [ND]partition->nand_disk[8].type :0 [ 1.113875] [ND]partition->nand_disk[9].size :-1 [ 1.119025] [ND]partition->nand_disk[9].type :-1 [ 1.124150] [ND]partition->nand_disk[10].size :-1 [ 1.129396] [ND]partition->nand_disk[10].type :-1 [ 1.134617] [ND]partition->nand_disk[11].size :-1 [ 1.139863] [ND]partition->nand_disk[11].type :-1 [ 1.145086] [ND]partition->nand_disk[12].size :-1 [ 1.150333] [ND]partition->nand_disk[12].type :-1 [ 1.155554] [ND]partition->nand_disk[13].size :-1 [ 1.160802] [ND]partition->nand_disk[13].type :-1 [ 1.166023] [ND]partition->nand_disk[14].size :-1 [ 1.171269] [ND]partition->nand_disk[14].type :-1 [ 1.176493] [ND]partition->nand_disk[15].size :-1 [ 1.181740] [ND]partition->nand_disk[15].type :-1 [ 1.186963] [ND]partition->nand_disk[16].size :-1 [ 1.192212] [ND]partition->nand_disk[16].type :-1 [ 1.197458] [ND]partition->nand_disk[17].size :-1 [ 1.202681] [ND]partition->nand_disk[17].type :-1 [ 1.207927] [ND]partition->nand_disk[18].size :-1 [ 1.213150] [ND]partition->nand_disk[18].type :-1 [ 1.218395] [ND]partition->nand_disk[19].size :-1 [ 1.223618] [ND]partition->nand_disk[19].type :-1 [ 1.228863] [ND]partition->nand_disk[20].size :-1 [ 1.234085] [ND]partition->nand_disk[20].type :-1 [ 1.239330] [ND]partition->nand_disk[21].size :-1 [ 1.244554] [ND]partition->nand_disk[21].type :-1 [ 1.249809] [ND]partition->nand_disk[22].size :-1 [ 1.255030] [ND]partition->nand_disk[22].type :-1 [ 1.260282] [ND]partition->nand_disk[23].size :-1 [ 1.265503] [ND]partition->nand_disk[23].type :-1 [ 1.270750] [ND]phy_partition->PartitionNO :0 [ 1.275587] [ND]phy_partition->SectorNumsPerPage :8 [ 1.281026] [ND]phy_partition->PageNumsPerBlk :64 [ 1.286248] [ND]phy_partition->TotalBlkNum :479 [ 1.291300] [ND]phy_partition->FullBitmapPerPage :8 [ 1.296715] [ND]phy_partition->FreeBlock :0 [ 1.301380] [ND]phy_partition->TotalSectors :224768 [ 1.306795] [ND]phy_partition->StartBlock.Chip_NO :0 [ 1.312328] [ND]phy_partition->StartBlock.Block_NO :33 [ 1.318056] [ND]phy_partition->EndBlock.Chip_NO :0 [ 1.323374] [ND]phy_partition->EndBlock.Block_NO :511 [ 1.329004] [ND]phy_partition->next_phy_partition :0 [ 1.334519] [ND]phy_partition->PartitionNO 0 FACTORY BAD BLOCK: [ 1.341212] [ND]phy_partition->PartitionNO 0 NEW BAD BLOCK: [ 1.347522] [ND]build 1 phy_partition ! [ 1.351780] [ND]nand_info->type :0 [ 1.355553] [ND]nand_info->SectorNumsPerPage :8 [ 1.360607] [ND]nand_info->BytesUserData :16 [ 1.365345] [ND]nand_info->PageNumsPerBlk :64 [ 1.370205] [ND]nand_info->BlkPerChip :512 [ 1.374751] [ND]nand_info->FirstBuild :0 [ 1.379130] [ND]nand_info->FullBitmap :0 [ 1.383484] [ND]nand_info->bad_block_addr.Chip_NO :0 [ 1.389019] [ND]nand_info->bad_block_addr.Block_NO :0 [ 1.394626] [ND]nand_info->mbr_block_addr.Chip_NO :0 [ 1.400161] [ND]nand_info->mbr_block_addr.Block_NO :0 [ 1.405770] [ND]nand_info->no_used_block_addr.Chip_NO :0 [ 1.411692] [ND]nand_info->no_used_block_addr.Block_NO :33 [ 1.417810] [ND]nand_info->new_bad_block_addr.Chip_NO :0 [ 1.423709] [ND]nand_info->new_bad_block_addr.Block_NO :0 [ 1.429729] [ND]nand_info->new_bad_page_addr :65535 [ 1.435144] [ND]nand_info->partition_nums :1 [ 1.439907] [ND]sizeof partition:2384 [ 1.443972] [ND]nand_info->partition:0: [ 1.448257] [ND]size:0x36e00 [ 1.451452] [ND]cross_talk:0x0 [ 1.454839] [ND]attribute:0x0 [ 1.458155] [ND]start: chip:0 block:33 [ 1.462315] [ND]end : chip:0 block:511 [ 1.466571] [ND]boot :0xc3140000 [ 1.470177] [ND]boot->magic :0xaa55a5a5 [ 1.474435] [ND]boot->len :0x8000 [ 1.478135] [ND]boot->no_use_block :0x21 [ 1.482489] [ND]boot->uboot_start_block :0x8 [ 1.487251] [ND]boot->uboot_next_block :0x3a [ 1.491991] [ND]boot->logic_start_block :0x21 [ 1.496825] [ND]mbr len :4096 [ 1.500142] [ND]_PARTITION len :2560 [ 1.504110] [ND]_NAND_STORAGE_INFO len :512 [ 1.508777] [ND]_FACTORY_BLOCK len :2048 [ 1.513465] [ND]nand_partition0 [ 1.517214] [ND]nftl start:479,40 [ 1.521128] [ND]first [ 1.629273] [ND]before second 479 439. [ 1.965837] [NE]recover_phy_page_mapping no used page 44!! [ 1.972022] [ND]recover 51 44 [ 1.975496] [ND]free block nums is 51 ! [ 1.979832] [NE]not power on gc 51! [ 1.983706] [ND]nftl ok! [ 1.986591] [ND]max_erase_times = 65000 [ 1.992966] nanda: unknown partition table [ 1.999875] nandb: unknown partition table [ 2.006681] nandc: unknown partition table [ 2.013637] nandd: unknown partition table [ 2.019161] [NAND]nand init end [ 2.022981] lradc_battery_probe:lradc_battery_probe ++++++ [ 2.029198] lradc_battery_dts_parse:lradc_battery_dts_parse ++++++ [ 2.036108] key base: f1c23400 [ 2.039684] irq num: 116 ! [ 2.042697] battery_data_hw_init:battery_data_hw_init ++++++ [ 2.049087] lradc_battery_probe:lradc_battery_probe ------ [ 2.056514] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.064360] usbcore: registered new interface driver usb-storage [ 2.071391] usbcore: registered new interface driver usbserial [ 2.078047] usbcore: registered new interface driver usbserial_generic [ 2.085371] usbserial: USB Serial support registered for generic [ 2.092189] usbcore: registered new interface driver ch341 [ 2.098419] usbserial: USB Serial support registered for ch341-uart [ 2.105457] usbcore: registered new interface driver cp210x [ 2.111775] usbserial: USB Serial support registered for cp210x [ 2.118489] usbcore: registered new interface driver ftdi_sio [ 2.124944] usbserial: USB Serial support registered for FTDI USB Serial Device [ 2.133229] usbcore: registered new interface driver pl2303 [ 2.139551] usbserial: USB Serial support registered for pl2303 [ 2.146536] [hcd0]: usb host driver initialize........ [ 2.152654] [hcd0]: open_usb_clock [ 2.156492] pin_init [ 2.159201] get regulator_io is no nocare [ 2.163667] [hcd0]: host_init_state = 0 [ 2.167995] [hcd0]: platform is usb host [ 2.172510] [hcd0]: sunxi_hcd_init_controller: sunxi_hcd_host0: USB Host mode controller at f1c13000 using PIO, IRQ 115 [ 2.184577] sunxi_hcd_host0 1c13000.otghci0-controller: sunxi_hcd host driver [ 2.192571] sunxi_hcd_host0 1c13000.otghci0-controller: new USB bus registered, assigned bus number 1 [ 2.204131] hub 1-0:1.0: USB hub found [ 2.208474] hub 1-0:1.0: 1 port detected [ 2.213251] [hcd0]: [sunxi_hcd_host0]:hcd0 set_regulator_io:ON [ 2.219832] [hcd0]: sunxi_usb_host0_disable start [ 2.225065] [hcd0]: sunxi_hcd_wait_for_disconnect cnt=0 [ 2.230905] [hcd0]: -------sunxi_hcd0_soft_disconnect--------- [ 2.237384] wrn: hcd is not enable, need not stop hcd [ 2.243025] [hcd0]: [sunxi_hcd_host0]: Set USB Power OFF [ 2.248961] [hcd0]: [sunxi_hcd_host0]:hcd0 set_regulator_io:OFF [ 2.255615] [hcd0]: close_usb_clock [ 2.259575] [hcd0]: sunxi_usb_host0_disable end [ 2.265015] ++++++++++++++++ alpu_init +++++++++++++ [ 2.270718] proc create successtrimui_sunxi_gpio_init: ver Aug 1 2020 [ 2.281626] serial: 00000002ED [ 2.295024] Bypass Test OK! [ 2.298269] test enc [ 2.305822] ret=0 [ 2.308014] test dec [ 2.315696] ret=0 [ 2.317906] DEC: ARE LINK TEST 12 [ 2.321914] -------- keytabcheck_init ------- [ 2.328726] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v0.91 2018-5-29 14:19) Compiled in Aug 1 2020 at 07:15:49 [ 2.341231] sunxi-mmc sdc0: Can't get vmmc regulator string [ 2.347514] sunxi-mmc sdc0: Can't get vqmmc regulator string [ 2.353808] sunxi-mmc sdc0: Can't get vdmmc regulator string [ 2.360138] sunxi-mmc sdc0: Failed getting OCR mask: 0 [ 2.366759] sunxi-mmc sdc0: ***set host ocr*** [ 2.371979] sunxi-mmc sdc0: Got CD GPIO #131. [ 2.377260] sunxi-mmc sdc0: sdc set ios: clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.407200] sunxi-mmc sdc0: sdc set ios: clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 2.437530] sunxi-mmc sdc0: sdc set ios: clk 0Hz bm OD pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 2.448086] sunxi-mmc sdc0: base:0xf1c0f000 irq:108 [ 2.454729] hidraw: raw HID events driver (C) Jiri Kosina [ 2.462311] usbcore: registered new interface driver usbhid [ 2.468597] usbhid: USB HID core driver [ 2.474923] usbcore: registered new interface driver snd-usb-audio [ 2.483104] failed to get gpio-spk and gpio_num [ 2.490048] sunxi-internal-codec 1c23c00.codec: ASoC: DAPM unknown pin HPOUTR [ 2.498112] sunxi-internal-codec 1c23c00.codec: ASoC: DAPM unknown pin HPOUTL [ 2.506053] sunxi-internal-codec 1c23c00.codec: ASoC: DAPM unknown pin SPKL [ 2.513839] sunxi-internal-codec 1c23c00.codec: ASoC: DAPM unknown pin SPKR [ 2.521631] sunxi-codec-machine sound.2: ASoC: DAPM unknown pin External Speaker [ 2.536717] sunxi-codec-machine sound.2: sun3iw1codec <-> 1c23c00.cpudai0-controller mapping ok [ 2.546685] sunxi-codec-machine sound.2: ASoC: no sink widget found for MainMic Bias [ 2.555368] sunxi-codec-machine sound.2: ASoC: Failed to add route External MainMic -> direct -> MainMic Bias [ 2.566426] sunxi-codec-machine sound.2: ASoC: no source widget found for MainMic Bias [ 2.575265] sunxi-codec-machine sound.2: ASoC: Failed to add route MainMic Bias -> direct -> MIC1P [ 2.585254] sunxi-codec-machine sound.2: ASoC: no source widget found for MainMic Bias [ 2.594085] sunxi-codec-machine sound.2: ASoC: Failed to add route MainMic Bias -> direct -> MIC1N [ 2.609430] ipip: IPv4 over IPv4 tunneling driver [ 2.615733] gre: GRE over IPv4 demultiplexor driver [ 2.621279] ip_gre: GRE over IPv4 tunneling driver [ 2.628753] TCP: cubic registered [ 2.632455] Initializing XFRM netlink socket [ 2.637351] NET: Registered protocol family 17 [ 2.642368] NET: Registered protocol family 15 [ 2.647844] VFP support v0.3: not present [ 2.653289] [LCD]lcd_module_init [ 2.658394] enhance_en=1 [ 2.661270] matrixresult:(0x0, 0x3c4, 0x0, 0x0) [ 2.666437] pll_freq=297000000HZ, lcd_dclk_freq=19000000HZ, clk_div=15 [ 2.673832] clk_div=15 [ 2.676468] LCD_panel_init ! [ 2.679855] LCD_panel_hw_reset ! [ 3.037016] LCD_panel_hw_reset done ! [ 3.187025] LCD_panel_io_term ! [ 3.190572] [LCD]open, step 0 finish sleep 50 ms [ 3.247071] [LCD]open, step 1 finish sleep 100 ms [ 3.357859] [LCD]open, step 2 finish sleep 30 ms [ 3.397228] sun3iw1p1-pinctrl pio: missing allwinner,pins property in node pwm1 [ 3.405368] platform pwm1.1: pinctrl_get failed! [ 3.410703] [LCD]open, step 3 finish sleep 0 ms [ 3.419963] [LCD]lcd_module_init finish [ 3.424660] usb_serial_number:20080411 [ 3.429339] [udc]: alloc request: ep(0xc0632180, ep0, 64), req(0xc31e4960) [ 3.437096] [udc]: sunxi_udc_set_selfpowered_2413: usb device is not active [ 3.444869] [udc]: sunxi_udc_pullup, is_on = 0 [ 3.449855] [udc]: sunxi_udc_set_pullup_2430: usb device is not active [ 3.457301] file system registered [ 3.463290] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 3.471061] android_usb gadget: Number of LUNs=1 [ 3.476239] lun0: LUN: removable file: (no medium) [ 3.482441] [udc]: sunxi_udc_set_selfpowered_2413: usb device is not active [ 3.490400] android_usb gadget: android_usb ready [ 3.495638] [udc]: [sunxi_usb_udc]: binding gadget driver 'android_usb' [ 3.503153] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 3.510429] ALSA device list: [ 3.513744] #0: audiocodec [ 3.518184] EXT2-fs (nandd): error: couldn't mount because of unsupported optional features (40) [ 3.528629] EXT4-fs (nandd): couldn't mount as ext3 due to feature incompatibilities [ 3.568249] EXT4-fs (nandd): mounted filesystem without journal. Opts: (null) [ 3.576343] VFS: Mounted root (ext4 filesystem) readonly on device 93:48. [ 3.585383] devtmpfs: mounted [ 3.589437] Freeing unused kernel memory: 124K (c0529000 - c0548000) mount: mounting none on /dev failed: Device or resource busy mount: mounting pstore on /sys/fs/pstore failed: No such file or directory mount: mounting /dev/by-name/rootfs_data on /overlay failed: No such file or directory Mount Failed: formating /dev/by-name/rootfs_data to ext4 ... /pseudo_init: line 340: mkfs.ext4: not found [ 5.449541] EXT4-fs (nandd): warning: mounting unchecked fs, running e2fsck is recommended [ 5.459227] EXT4-fs (nandd): re-mounted. Opts: (null) -- run rc.preboot -- -- set volume -- -- play music -- -- end -- playing '/etc/enter.wav': 2 ch, 48000 hz, 16 bit [ 6.248295] bdev is c31fdc00, dev is c3068410 [ 6.253195] request gpio 0, GPIO Key Up [ 6.267205] request gpio 130, GPIO Key Down [ 6.287224] request gpio 132, GPIO Key Left [ 6.292046] request gpio 136, GPIO Key Right [ 6.296802] request gpio 113, GPIO Key A [ 6.310477] request gpio 108, GPIO Key B [ 6.314888] request gpio 98, GPIO Key X [ 6.320288] request gpio 115, GPIO Key Y [ 6.324813] request gpio 109, GPIO Key START [ 6.330679] request gpio 110, GPIO Key SELECT [ 6.336092] request gpio 139, GPIO Key MENU [ 6.341949] request gpio 96, GPIO Key L [ 6.346261] request gpio 97, GPIO Key R [ 6.350666] gpio-keys-polled platform_set_drvdata, dev is c3068410 [ 6.357677] gpio-keys-polled input_register_polled_device, dev is c3068410 [ 6.367571] input: gpio_keys.6 as /devices/soc/gpio_keys.6/input/input0 [ 6.375023] gpio_keys_polled_open c31fdc00 c3216000 begin [ 6.381128] gpio_keys_polled_open c31fdc00 c3216000 end [ 6.413033] gpio-keys-polled report initial state of the 13 buttons [ 6.420178] gpio-keys-polled probe finished, dev is c3068410, pdev is c3068400 -- run rc.final -- insmod F1C200s-board Linux login: add device 1: /dev/input/event0 name: "gpio_keys.6" trimui_sunxi_gpio_init: ver Aug 1 2020 serial 00000002ED 0 test dec vtpath = /dev/vc/2, fd = -1 vtpath = /dev/tty2, fd = 4 Current VT: 2 FB_VideoInit shadow_fb is 0 ttf inited SDL_OpenAudio freq 44100, format 32784, channels 2, samples 2048 Mix_OpenAudio: No available audio device FB_LeaveGraphicsMode trimui_sunxi_gpio_init: ver Aug 1 2020 serial 00000002ED 0 test dec vtpath = /dev/vc/2, fd = -1 vtpath = /dev/tty2, fd = 4 Current VT: 2 FB_VideoInit shadow_fb is 0 ttf inited SDL_OpenAudio freq 44100, format 32784, channels 2, samples 2048 opened /dev/dsp audio_fd is 5 open audio true sdl inited SDL_GetVideoMode 320x240 16 -> 320x240 16 FB_EnterGraphicsMode start iotcl VT_GETSTATE start iotcl VT_ACTIVATE start 1 iotcl VT_WAITACTIVE start iotcl KDGKBMODE start iotcl KDSKBMODE start 3 iotcl KDSETMODE start iotcl VT_LOCKSWITCH start FB_EnterGraphicsMode end SDL_CreateShadowSurface 16 SDL_SetVideoMode publicsurface 0x1b56048, shadowsurface 0x1b56048, videosurface 0x1b4c350 Double buf enabled 0, use SDL_UpdateRect when flip screen inited [InitKeyShm]: create shm fail : File exists, size 48 Load Music /usr/trimui/res/sound/click.wav Load Music /etc/enter.wav Load Music /usr/trimui/res/sound/MusMus-BGM-091.mp3 load font height is 26 read lang file /usr/trimui/res/lang/en.lang ok=1 genShortLangFile en.lang index 0, size 1 read lang file /usr/trimui/res/lang/ch.lang ok=1 genShortLangFile ch.lang index 1, size 2 dir is (null) open applist /mnt/SDCARD/Apps/applist.json fail set card 0 ctl 22 to 31 setup_keymap 0 A,B,X,Y,L,R setLCDBrightness 130 restore background music volume 32 try to restore open /tmp/state.json fail nothing to restore swap size is 0 LoginLinux login: