TRIMUI SMART
UART腳位
司徒找到一個還不錯的位置
裝入後
需要挖掉一些東西
還算可以～
縫隙等之後在用3D印表機列印補起來～
連接UART
為了方便使用USB Type-C連接，司徒最後改成使用PL-2303SA
Miyoo-Mini TXD連接到RX
Miyoo-Mini RXD連接到TX
跳線後
裝上外殼
完成
115200bps
HELLO! BOOT0 is starting! boot0 version : 4.2.0 boot0 commit : ec3a840e24084ed1f604eb32b8f07791ec77ff75 fel flag = 0x00000000 rtc[0] value = 0x00000000 rtc[1] value = 0x00000000 rtc[2] value = 0x00000000 rtc[3] value = 0x00000000 rtc[4] value = 0x00000000 rtc[5] value = 0x00000000 rtc[6] value = 0x00000000 rtc[7] value = 0x00000000 DRAM DRIVE INFO: V0.9 DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3) DRAM CLK = 696 MHz DRAM zq value: 000039bb DRAM size = 128 MB dram size =128 card boot number = 2 card no is 2 sdcard 2 line count 8 [mmc]: mmc driver ver 2017-04-25 17:18:00 [mmc]: ***Try SD card 2*** [mmc]: mmc 2 cmd 8 timeout, err 00000100 [mmc]: mmc 2 cmd 8 err 00000100 [mmc]: mmc 2 send if cond failed [mmc]: mmc 2 cmd 55 timeout, err 00000100 [mmc]: mmc 2 cmd 55 err 00000100 [mmc]: mmc 2 send app cmd failed [mmc]: ***Try MMC card 2*** [mmc]: MMC ver 4.0 [mmc]: SD/MMC Card: 1bit, capacity: 7456MB [mmc]: vendor: Man 00150100 Snr 06c8a9fa [mmc]: product: 8GTF4 [mmc]: revision: 5.2 [mmc]: ***SD/MMC 2 init OK!!!*** sdcard 2 init ok The size of uboot is 000c8000. sum=f1ca9a67 src_sum=f1ca9a67 set_mmc_para,sdly 50M 0 set_mmc_para,sdly 25M 0 Succeed in loading uboot from sdmmc flash. Ready to disable icache. Jump to secend Boot. [ 0.831] U-Boot 2011.09-rc1-00000-g23969d8-dirty (Jul 15 2022 - 15:56:22) Allwinner Technology [ 0.840]version: 1.1.0 [ 0.843]uboot commit : 23969d89e73cd0f31082bd5afcd06e64d6e72d72 [ 0.849]pmbus: ready axp read error probe axp20x failed axp_probe error [ 1.215]PMU: pll1 1200 Mhz,PLL6=600 Mhz AXI=400 Mhz,AHB=200 Mhz, APB1=100 Mhz fel key new mode run key detect fel_key_mode:0 no key found no key input dram_para_set start dram_para_set end [ 1.354]DRAM: 128 MiB relocation Offset is: 061d6000 save config for small mem_size board.c 659 workmode = 0 MMC: 2 [ 1.411][mmc]: mmc driver ver 2018-06-25 14:21:00 [ 1.416][mmc]: get sdc_phy_wipe fail. [ 1.420][mmc]: get sdc0 sdc_erase fail. [ 1.424][mmc]: get sdc2 sdc_hw_rst fail. [ 1.428][mmc]: get sdc_2xmode ok, val = 1 [ 1.432][mmc]: get sdc_ddrmode ok, val = 1 [ 1.436][mmc]: get sdc_f_max fail,use default 50000000Hz [ 1.442][mmc]: get card_line ok, card_line = 8 [ 1.446][mmc]: get sdc_test fail. [ 1.450][mmc]: get sdc_ex_dly_used fail,use default [ 1.455][mmc]: SUNXI SD/MMC: 2 [ 1.459][mmc]: mmc_config_clock: clk 400000 [ 1.467][mmc]: *Try SD card 2* [ 1.470][mmc]: mmc 2 cmd 8 err 100 [ 1.474][mmc]: mmc send if cond failed [ 1.478][mmc]: mmc 2 cmd 55 err 100 [ 1.482][mmc]: send app cmd failed [ 1.486][mmc]: *Try MMC card 2* [ 1.520][mmc]: mmc_config_clock: clk 25000000 [ 1.525][mmc]: mmc re-update_phase [ 1.528][mmc]: mmc re-update_phase [ 1.532][mmc]: mmc re-update_phase [ 1.536][mmc]: ddr8 [ 1.538][mmc]: mmc re-update_phase [ 1.541][mmc]: mmc_config_clock: clk 25000000 [ 1.546][mmc]: mmc_config_clock: clk 50000000 [ 1.550][mmc]: CID 0x15010038 0x47544634 0x5206c8a9 0xfab399d5 [ 1.556][mmc]: MMC v5.1 [ 1.559][mmc]: mmc clk 50000000 [ 1.562][mmc]: SD/MMC Card: 8bit, capacity: 7456MB [ 1.567][mmc]: boot0 capacity: 4000KB,boot1 capacity: 4000KB [ 1.573][mmc]: ***SD/MMC 2 init OK!!!*** [ 1.577][mmc]: erase_grp_size:0x400WrBlk * 0x200 = 0x80000 Byte [ 1.583][mmc]: secure_feature 0x55 [ 1.587][mmc]: secure_removal_type 0x39 [ 1.591]sunxi flash init ok In: serial Out: serial Err: serial the flash size is 7456 MB --------fastboot partitions-------- -total partitions:8- -name- -start- -size- bootlogo : 400000 80000 env : 480000 c0000 boot : 540000 480000 rootfs : 9c0000 8180000 rootfs_data : 8b40000 c0000 misc : 8c00000 c0000 private : 8cc0000 c0000 UDISK : 8d80000 c9280000 ----------------------------------- base bootcmd=run setargs_nand boot_normal bootcmd set setargs_mmc key 0 cant find rcvy value cant find fstbt value misc partition found to be run cmd=run setargs_mmc boot_normal pd cfg1 val is 77777771 pd data val is 1 pd data val is 0 pd data val is 1 pb cfg1 val is 21777722 pb data val is 40 pe cfg1 val is 77777700 pe data val is 300 Net: eth0Warning: failed to set MAC address , usb_etherWarning: failed to set MAC address WORK_MODE_BOOT addr = 47000000 sunxi_read_bootlogo: read bootlogo partition successful [ 1.740]Hit any key to stop autoboot: 0 fatload partition name: boot -> 2 reading uImage ## Booting kernel from Legacy Image at 40007fc0 ... Image Name: ARM OpenWrt Linux-3.4.39 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3631888 Bytes = 3.5 MiB Load Address: 40008000 Entry Point: 40008000 XIP Kernel Image ... OK OK [ 1.817][mmc]: mmc exit start [ 1.821][mmc]: mmc_config_clock: clk 50000000 [ 1.825][mmc]: mmc_config_clock: clk 400000 [ 1.834][mmc]: mmc 2 cmd 8 err 100 [ 1.838][mmc]: mmc send if cond failed [ 1.843][mmc]: mmc 2 cmd 55 err 100 [ 1.847][mmc]: send app cmd failed [ 1.859][mmc]: get sdc_phy_wipe fail. [ 1.863][mmc]: get sdc0 sdc_erase fail. [ 1.867][mmc]: get sdc2 sdc_hw_rst fail. [ 1.871][mmc]: get sdc_2xmode ok, val = 1 [ 1.875][mmc]: get sdc_ddrmode ok, val = 1 [ 1.879][mmc]: get sdc_f_max fail,use default 50000000Hz [ 1.885][mmc]: get card_line ok, card_line = 8 [ 1.889][mmc]: get sdc_test fail. [ 1.893][mmc]: get sdc_ex_dly_used fail,use default [ 1.898][mmc]: mmc 2 exit ok reload config to 0x41000000 [ 1.901] Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.39 (alfchen@alfchen-NUC) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #547 Sat Sep 24 16:55:30 UTC 2022 [ 0.000000] cma: CMA: reserved 32 MiB at 46000000 [ 0.000000] Kernel command line: boot_type=2 disp_para=2 fb_base=0x47000000 config_size=29696 console=ttyS2,115200 earlyprintk=ttyS2,115200 root=/dev/mmcblk0p7 init=/pseudo_init rdinit=/4 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Memory: 128MB = 128MB total [ 0.000000] Memory: 89548k/89548k available, 41524k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) [ 0.000000] lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc0661000 (6500 kB) [ 0.000000] .init : 0xc0661000 - 0xc0686000 ( 148 kB) [ 0.000000] .data : 0xc0686000 - 0xc06dddd0 ( 352 kB) [ 0.000000] .bss : 0xc06dddf4 - 0xc072c1b0 ( 313 kB) [ 0.000000] NR_IRQS:544 [ 0.000000] Architected local timer running at 24.00MHz. [ 0.000000] Switching to timer-based delay loop [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms [ 0.000000] Console: colour dummy device 80x30 [ 0.000112] Calibrating delay loop (skipped), value calculated using timer frequency.. 4800.00 BogoMIPS (lpj=24000000) [ 0.000127] pid_max: default: 32768 minimum: 301 [ 0.000235] Mount-cache hash table entries: 512 [ 0.000651] CPU: Testing write buffer coherency: ok [ 0.000826] Setting up static identity map for 0x404f5cb0 - 0x404f5d08 [ 0.001333] devtmpfs: initialized [ 0.003005] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.003156] pinctrl core: initialized pinctrl subsystem [ 0.005135] NET: Registered protocol family 16 [ 0.006341] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.006599] script_sysfs_init success [ 0.007564] gpiochip_add: registered GPIOs 0 to 223 on device: sunxi-pinctrl [ 0.008250] sunxi-pinctrl sunxi-pinctrl: initialized sunXi PIO driver [ 0.008862] gpiochip_add: registered GPIOs 1024 to 1031 on device: axp-pinctrl [ 0.011082] script config pll_isp to 360 Mhz [ 0.011103] Not Found clk pll_video in script [ 0.011112] script config pll_ve to 360 Mhz [ 0.011125] Not Found clk pll_periph0 in script [ 0.011131] Not Found clk pll_de in script [ 0.049444] bio: create slab <bio-0> at 0 [ 0.049762] pwm module init! [ 0.053795] SCSI subsystem initialized [ 0.054117] usbcore: registered new interface driver usbfs [ 0.054286] usbcore: registered new interface driver hub [ 0.054462] usbcore: registered new device driver usb [ 0.054918] twi_chan_cfg()348 - [twi0] has no twi_regulator. [ 0.054930] twi_chan_cfg()348 - [twi1] has no twi_regulator. [ 0.056336] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.057101] Bluetooth: Core ver 2.16 [ 0.057274] NET: Registered protocol family 31 [ 0.057283] Bluetooth: HCI device and connection manager initialized [ 0.057292] Bluetooth: HCI socket layer initialized [ 0.057299] Bluetooth: L2CAP socket layer initialized [ 0.057316] Bluetooth: SCO socket layer initialized [ 0.057789] cfg80211: Calling CRDA to update world regulatory domain [ 0.058692] Switching to clocksource arch_sys_counter [ 0.067073] NET: Registered protocol family 2 [ 0.067273] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.067640] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.067699] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.067737] TCP: Hash tables configured (established 4096 bind 4096) [ 0.067745] TCP: reno registered [ 0.067757] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.067773] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.068001] NET: Registered protocol family 1 [ 0.068522] standby_mode = 1. [ 0.068527] wakeup src cnt is : 3. [ 0.068547] config_pmux_para: script_parser_fetch err. [ 0.068553] pmu1_enable = 0x0. [ 0.068563] config_pmux_para: script_parser_fetch err. [ 0.068569] pmu2_enable = 0x0. [ 0.068576] add_sys_pwr_dm: get ldo name failed [ 0.068582] add_sys_pwr_dm: get ldo name failed [ 0.068588] add_sys_pwr_dm: get ldo name failed [ 0.068594] add_sys_pwr_dm: get ldo name failed [ 0.068600] add_sys_pwr_dm: get ldo name failed [ 0.068606] add_sys_pwr_dm: get ldo name failed [ 0.068612] add_sys_pwr_dm: get ldo name failed [ 0.068618] add_sys_pwr_dm: get ldo name failed [ 0.068624] add_sys_pwr_dm: get ldo name failed [ 0.068630] add_sys_pwr_dm: get ldo name failed [ 0.068636] after inited: sys_mask config = 0x0. [ 0.068643] dynamic_standby enalbe = 0x0. [ 0.068682] sunxi_reg_init enter [ 0.070684] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.070734] msgmni has been set to 238 [ 0.071140] io scheduler noop registered [ 0.071149] io scheduler deadline registered [ 0.071197] io scheduler cfq registered (default) [ 0.071203] [DISP]disp_module_init [ 0.071881] [DISP]disp_probe [ 0.071944] cmdline,disp=2 [ 0.071950] bsp_disp_init-----------------1 [ 0.072388] [DISP] disp_get_rotation_sw,line:77:disp 0 out of range? g_rot_sw=0 [ 0.072398] [DISP] disp_init_connections,line:289:NULL pointer: 0, 0 [ 0.077563] disp_init-----------------2 [ 0.077809] [DISP] lcd_clk_config,line:896:disp 0, clk: pll(340000000),clk(170000000),dclk(17000000) dsi_rate(340000000) [ 0.078454] [DISP]disp_module_init finish [ 0.078815] sw_uart_get_devinfo()2038 - uart0 has no uart_regulator. [ 0.078828] sw_uart_get_devinfo()2038 - uart1 has no uart_regulator. [ 0.078838] sw_uart_get_devinfo()2038 - uart2 has no uart_regulator. [ 0.079623] uart0: ttyS0 at MMIO 0x1c28000 (irq = 32) is a SUNXI [ 0.080210] uart1: ttyS1 at MMIO 0x1c28400 (irq = 33) is a SUNXI [ 0.080672] uart2: ttyS2 at MMIO 0x1c28800 (irq = 34) is a SUNXI [ 0.080683] sw_uart_pm()1296 - uart2 clk is already enable [ 0.080697] sw_console_setup()1696 - console setup baud 115200 parity n bits 8, flow n [ 0.762261] console [ttyS2] enabled [ 0.771765] loop: module loaded [ 1.026179] no ldo for moto, ignore it [ 1.030353] no ldo moto voltage config, ignore it [ 1.036145] charge_state script_get_item err [ 1.040912] pwmleds debug gpio driver init [ 1.045451] [pwm_leds]: pwm_leds_ctrl_init: 382===into [ 1.051253] [pwm_leds] pwm_request pwm0 fail! [ 1.056081] pwm_leds_init is err============== [ 1.061643] sunxi_spi_chan_cfg()1389 - [spi-0] has no spi_regulator. [ 1.069422] spi spi0: master is unqueued, this is deprecated [ 1.076362] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.103731] sunxi-ehci sunxi-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.112691] sunxi-ehci sunxi-ehci.1: new USB bus registered, assigned bus number 1 [ 1.121346] sunxi-ehci sunxi-ehci.1: irq 104, io mem 0xf1c1a000 [ 1.140039] sunxi-ehci sunxi-ehci.1: USB 0.0 started, EHCI 1.00 [ 1.147463] hub 1-0:1.0: USB hub found [ 1.151709] hub 1-0:1.0: 1 port detected [ 1.156280] sunxi-ehci sunxi-ehci.1: remove, state 1 [ 1.161829] usb usb1: USB disconnect, device number 1 [ 1.168980] sunxi-ehci sunxi-ehci.1: USB bus 1 deregistered [ 1.185548] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.212572] sunxi-ohci sunxi-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver [ 1.221137] sunxi-ohci sunxi-ohci.1: new USB bus registered, assigned bus number 1 [ 1.229584] sunxi-ohci sunxi-ohci.1: irq 105, io mem 0xf1c1a400 [ 1.294811] hub 1-0:1.0: USB hub found [ 1.298986] hub 1-0:1.0: 1 port detected [ 1.303605] sunxi-ohci sunxi-ohci.1: remove, state 1 [ 1.309118] usb usb1: USB disconnect, device number 1 [ 1.315416] sunxi-ohci sunxi-ohci.1: USB bus 1 deregistered [ 1.332079] usbcore: registered new interface driver cdc_acm [ 1.338358] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.347276] Initializing USB Mass Storage driver... [ 1.352878] usbcore: registered new interface driver usb-storage [ 1.359570] USB Mass Storage support registered. [ 1.365320] file system registered [ 1.371711] android_usb gadget: Mass Storage Function, version: 2009/09/11 [ 1.379367] android_usb gadget: Number of LUNs=1 [ 1.384548] lun0: LUN: removable file: (no medium) [ 1.390652] android_usb gadget: android_usb ready [ 1.396489] [RTC] WARNING: Rtc time will be wrong!! [ 1.402289] sunxi-rtc sunxi-rtc: rtc core: registered sunxi-rtc as rtc0 [ 1.409859] i2c /dev entries driver [ 1.414149] ++++++++++++++++ alpu_init +++++++++++++ [ 1.419684] proc create success [ 1.423225] proc serial create success [ 1.431107] serial: 0000001D50 [ 1.444888] Bypass Test OK! [ 1.453687] ret=0 [ 1.461445] ret=0 [ 1.463861] sunxi_pwr_key_fetch_sysconfig_para pwr_ctrl is not used in config [ 1.471801] =========script_get_err============ [ 1.477307] Bluetooth: HCI UART driver ver 2.2.74e8f89.20210423-153941 [ 1.484584] Bluetooth: HCI H4 protocol initialized [ 1.489886] Bluetooth: HCI Realtek H5 protocol initialized [ 1.495986] rtk_btcoex: rtk_btcoex_init: version: 1.2 [ 1.501592] rtk_btcoex: create workqueue [ 1.506031] rtk_btcoex: alloc buffers 1408, 2240 for ev and l2 [ 1.514089] Synopsys Designware Multimedia Card Interface Driver[mmc]: SD/MMC/SDIO Host Controller Driver(v1.126 2018-10-15 14:05) Compiled in Aug 25 2022 at 08:27:41 [ 1.541010] no led1_active_low, sunxi_leds_fetch_sysconfig_para failed! [ 1.548369] =========script_get_err============ [ 1.553706] [led]:sunxi_led_init begin! [ 1.557959] =====led_sysconfig_para=====. [ 1.562472] led1 gpio number is 202 [ 1.566339] led1_trigger gpio number is default-on [ 1.571663] led2 gpio number is 203 [ 1.575525] led2_trigger gpio number is default-on [ 1.580846] led3 gpio number is 204 [ 1.584710] led3_trigger gpio number is default-on [ 1.596875] [audiocodec] main_mic_vol type err! [ 1.601932] [audiocodec] headset_mic_vol type err! [ 1.607350] *******************Try sdio******************* [ 1.614506] mmc0: req failed (CMD5): -110, retrying... [ 1.620629] asoc: sndcodec <-> sunxi-codec mapping ok [ 1.626356] mmc0: req failed (CMD5): -110, retrying... [ 1.633093] mmc0: req failed (CMD5): -110, retrying... [ 1.640122] u32 classifier [ 1.643143] Performance counters on [ 1.647393] Actions configured [ 1.651175] Netfilter messages via NETLINK v0.30. [ 1.656430] *******************Try sd ******************* [ 1.662471] nf_conntrack version 0.5.0 (1911 buckets, 7644 max) [ 1.669253] ctnetlink v0.93: registering with nfnetlink. [ 1.675355] IPv4 over IPv4 tunneling driver [ 1.680678] gre: GRE over IPv4 demultiplexor driver [ 1.686122] ip_gre: GRE over IPv4 tunneling driver [ 1.691466] *******************Try mmc******************* [ 1.698423] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.705766] TCP: cubic registered [ 1.711621] NET: Registered protocol family 17 [ 1.716583] NET: Registered protocol family 15 [ 1.721747] Bluetooth: RFCOMM TTY layer initialized [ 1.727182] Bluetooth: RFCOMM socket layer initialized [ 1.732905] Bluetooth: RFCOMM ver 1.11 [ 1.737058] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 1.743014] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 1.749821] 8021q: 802.1Q VLAN Support v1.8 [ 1.754873] ThumbEE CPU extension supported. [ 1.759786] Registering SWP/SWPB emulation handler [ 1.766128] sunxi-rtc sunxi-rtc: hctosys: unable to read the hardware clock [ 1.774784] ALSA device list: [ 1.778134] #0: audiocodec [ 1.781649] Waiting for root device /dev/mmcblk0p7... [ 1.788020] mmc0: new high speed MMC card at address 0001 [ 1.794463] mmcblk0: mmc0:0001 8GTF4R 7.28 GiB [ 1.799569] mmcblk0boot0: mmc0:0001 8GTF4R partition 1 4.00 MiB [ 1.806281] mmcblk0boot1: mmc0:0001 8GTF4R partition 2 4.00 MiB [ 1.813808] mmcblk0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 > [ 1.819450] mmcblk0: p1 size 14948352 extends beyond EOD, truncated [ 1.829067] mmcblk0boot1: unknown partition table [ 1.835458] mmcblk0boot0: unknown partition table [ 1.841121] *******************mmc init ok ******************* [ 1.894522] EXT4-fs (mmcblk0p7): warning: mounting unchecked fs, running e2fsck is recommended [ 1.905492] EXT4-fs (mmcblk0p7): mounted filesystem without journal. Opts: (null) [ 1.913861] VFS: Mounted root (ext4 filesystem) on device 179:7. [ 1.921044] devtmpfs: mounted [ 1.924527] Freeing init memory: 148K [ 2.109779] EXT4-fs (mmcblk0p8): mounted filesystem without journal. Opts: (null) skip mount overlayfs as now rootfs not squashfs [ 2.140485] EXT4-fs (mmcblk0p7): re-mounted. Opts: (null) [ 2.263724] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) ------run rc.modules file----- insmod sound modules insmod uvcvideo modules [ 2.442359] android_usb: already disabled ------run rc.final file----- insmod wifi modules [ 2.487606] adb_open [ 2.491496] adb_bind_config Trying to connect to SWUpdate... [ 2.508919] mtp_bind_config numid=21,iface=MIXER,name='SPK_L Mux' ; type=ENUMERATED,access=rw------,values=1,items=2 ; Item #0 'MIXER_L Switch' ; Item #1 'MIXR+MIXL' : values=0 numid=22,iface=MIXER,name='SPK_R Mux' ; type=ENUMERATED,access=rw------,values=1,items=2 ; Item #0 'MIXER_R Switch' ; Item #1 'Lineout_l for diff Switch' : values=0 numid=3,iface=MIXER,name='Lineout volume' ; type=INTEGER,access=rw---R--,values=1,min=0,max=31,step=0 : values=30 | dBscale-min=-48.00dB,step=1.50dB,mute=0 numid=26,iface=MIXER,name='Right Output Mixer DACR Switch' ; type=BOOLEAN,access=rw------,values=1 : values=on numid=31,iface=MIXER,name='Left Output Mixer DACL Switch' ; type=BOOLEAN,access=rw------,values=1 : values=on numid=1,iface=MIXER,name='digital volume' ; type=INTEGER,access=rw---R--,values=1,min=0,max=63,step=0 : values=0 | dBscale-min=-74.24dB,step=0.00dB,mute=0 BusyBox v1.27.2 () built-in shell (ash) _____ _ __ _ |_ _||_| ___ _ _ | | |_| ___ _ _ _ _ | | _ | || | | |__ | || || | ||_'_| | | | || | || _ | |_____||_||_|_||___||_,_| |_| |_||_|_||_|_| Tina is Based on OpenWrt! ---------------------------------------------- Tina Linux (Neptune, 5C1C9C53) ---------------------------------------------- root@sun8i:/# add device 1: /dev/input/event0 name: "gpio-keys-polled" adc_thread loop trimui_sunxi_gpio_init: ver Nov 6 2021 serial 7878787878 0 test dec LLLLLLLLLLLLLLLL seria[ 5.954966] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 l 0000001D50 wifi monitor start[ 5.966204] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 ...sdl timer sdl video FB_Vide[ 5.974602] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 oInit FBIOPUT_VSCREENINFO vinfo [ 5.984051] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 yoff is 0, 240x320 new thread_w[ 5.994178] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 ifi_monitor: pid 750 tid 3054404[ 6.003741] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 688 (0xb60e8450) bt_thread star[ 6.013904] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 t [ 6.023435] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 [ 6.031033] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 [ 6.038263] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 [ 6.045802] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 [ 6.053070] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 [ 6.060762] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 [ 6.068131] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 [ 6.075737] [DISP] var_to_disp_fb,line:503:invalid bits_per_pixel :8 [ 6.083035] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.095807] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.108382] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.121180] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.138747] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.151457] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.164259] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.176876] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.189651] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.202207] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.214966] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.227563] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.240352] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.252918] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> [ 6.265682] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:24,red.offset:16,green.offset:8,blue.offset:0> sdl audio SDL_AudioInit(nil), flags 21, SDL_initialized 21 SDL_AudioInit(nil) ok sdl joystick sdl cdrom sdl init ok ttf inited SDL_OpenAudio freq 44100, format 32784, channels 2, samples 128, current_audio (nil) sdl timer sdl video sdl audio SDL_AudioInit(alsa), flags 10, SDL_initialized 21 driver_name is alsa Audio_Available snd_pcm_open error: Success , device default SDL_AudioInit ok SDL_AudioInit(alsa) ok sdl joystick sdl cdrom sdl init ok snd_pcm_open default return 0 [setparam] hwparams.format=2 channel:2 rate:44100 period_time:0, period_frames:0 [setparam] period_time=0 [setparam] period_frames=940 ============================================ buffer_time:0, buffer_frames:5644 [setparam] buffer_time=0 [setparam] buffer_frames=37[ 6.521599] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:0,red.offset:0,green.offset:0,blue.offset:0> [ 6.521620] [DISP] var_to_disp_fb,line:497:[FB]invalid format<transp.offset:0,red.offset:0,green.offset:0,blue.offset:0> 63 ============================================ after period size sw param done sw buffer done sw nonblock done open audio true sdl inited FB_EnterGraphicsMode start iotcl VT_GETSTATE start iotcl VT_ACTIVATE start 1 2 iotcl VT_WAITACTIVE start iotcl KDGKBMODE start iotcl KDSKBMODE start 3 iotcl KDSETMODE start iotcl VT_LOCKSWITCH start FB_EnterGraphicsMode end screen inited [InitKeyShm]: create shm fail : File exists, size 64 open /mnt/SDCARD/Themes cpu freq 0M init_skin /usr/trimui/res/ open /usr/trimui/res/OPPOSans-B-2.ttf 14 open /usr/trimui/res/OPPOSans-B-2.ttf 16 open /usr/trimui/res/OPPOSans-B-2.ttf 18 open /usr/trimui/res/OPPOSans-B-2.ttf 16 Load Music /usr/trimui/res/sound/click.wav Load Music /etc/enter.wav Load Music /usr/trimui/res/sound/MusMus-BGM-091.mp3 load font height is 22 read lang file /usr/trimui/res/lang/en.lang ok=1 genShortLangFile en.lang index 0, size 1 read lang file /usr/trimui/res/lang/ch.lang ok=1 genShortLangFile ch.lang index 1, size 2 battery mode 0x00000000 -> 0x00c0004d dir is (null) open /mnt/SDCARD/Emus open /mnt/UDISK/Emus open /mnt/SDCARD/Apps open /mnt/UDISK/Apps set card 0 ctl 2 to 6 setup_keymap 0 A,B,X,Y,L,R setLCDBrightness 255 restore background music volume 64 -> 128 try to restore open /tmp/state.json fail nothing to restore createMenu 0, . 0 idxs restored swap size is 0 runWindows ================= lcd_fb_init =============== [ 6.856737] *******************Try sdio******************* [ 6.865210] mmc2: card claims to support voltages below the defined range. These will be ignored. [ 6.886604] mmc2: new high speed SDIO card at address 0001 [ 7.088024] *******************sdio init ok******************* [ 8.030144] Bluetooth: h5_open [ 8.033551] Bluetooth: hci_uart_register_dev [ 8.043383] rtk_btcoex: Open BTCOEX [ 8.050453] rtk_btcoex: BTCOEX hci_rev 0xaaa8 [ 8.055300] rtk_btcoex: BTCOEX lmp_subver 0x2df5 wififlag 1, hostapflag 0 [ 10.090041] Bluetooth: __hci_uart_flush: hdev c4cbf000 tty c5b6f400 [ 10.106795] Bluetooth: hci_uart_close: hdev c4cbf000 [ 10.112349] Bluetooth: __hci_uart_flush: hdev c4cbf000 tty c5b6f400 [ 10.121226] rtk_btcoex: Close BTCOEX [ 10.125202] rtk_btcoex: -x [ 10.563082] rtk_btcoex: Open BTCOEX [ 10.571413] rtk_btcoex: BTCOEX hci_rev 0xaaa8 [ 10.576253] rtk_btcoex: BTCOEX lmp_subver 0x2df5 [ 18.940035] Bluetooth: hu c4cd2940 retransmitting 1 pkts