GCW Zero
焊接UART接頭
UART的位置如下：
完成
UART輸出訊息(Baudrate: 57600bps)
UBIBoot by Paul Cercueil <paul@crapouillou.net>
MMC: FAT32 filesystem detected.
MMC: Loading kernel file...
Kernel loaded. Executing...
Linux version 3.12.0-dingux+ (steward@debian) (gcc version 4.9.1 (Buildroot 2014.05-gbb847
d4) ) #8 Tue Mar 28 22:07:13 CST 2017
bootconsole [early0] enabled
CPU revision is: 2ed1024f (Ingenic JZRISC)
FPU revision is: 00330000
CPU clock: 996MHz, System clock: 166MHz, Peripheral clock: 166MHz, Memory clock: 166MHz, A
UX clock 166MHz, AHB1 clock 166MHz, AHB2 clock 166MHz
Determined physical RAM map:
memory: 00535000 @ 00010000 (usable)
memory: 0004b000 @ 00545000 (usable after init)
User-defined physical RAM map:
memory: 0ffff000 @ 00000000 (usable)
memory: 10000000 @ 30000000 (usable)
Initrd not found or empty - disabling initrd
Zone ranges:
Normal [mem 0x00000000-0x1fffffff]
HighMem [mem 0x20000000-0x3fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x0fffefff]
node 0: [mem 0x30000000-0x3fffffff]
Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130047
Kernel command line: mem=0x0100M mem=0x0100M@0x30000000 root=/dev/loop0 root=/dev/mmcblk0p
1 rootfstype=vfat rootwait ro init=/sbin/init init=/mininit-syspart console=ttyS2,57600 co
nsole=tty0 fbcon=bind:0 rfkill.default_state=0 -- hwvariant=v20_mddr_512mb panic=5 conso
le=ttyS2,57600 console=tty0 boot=/dev/mmcblk0p1 loop0=/boot/rootfs.squashfs root=/dev/loop
0 rfkill.default_state=0
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 510024K/524284K available (4231K kernel code, 198K rwdata, 892K rodata, 300K init,
109K bss, 14260K reserved, 262144K highmem)
NR_IRQS:384
Console: colour dummy device 80x25
console [tty0] enabled, bootconsole disabled
Linux version 3.12.0-dingux+ (steward@debian) (gcc version 4.9.1 (Buildroot 2014.05-gbb847
d4) ) #8 Tue Mar 28 22:07:13 CST 2017
bootconsole [early0] enabled
CPU revision is: 2ed1024f (Ingenic JZRISC)
FPU revision is: 00330000
CPU clock: 996MHz, System clock: 166MHz, Peripheral clock: 166MHz, Memory clock: 166MHz, A
UX clock 166MHz, AHB1 clock 166MHz, AHB2 clock 166MHz
Determined physical RAM map:
memory: 00535000 @ 00010000 (usable)
memory: 0004b000 @ 00545000 (usable after init)
User-defined physical RAM map:
memory: 0ffff000 @ 00000000 (usable)
memory: 10000000 @ 30000000 (usable)
Initrd not found or empty - disabling initrd
Zone ranges:
Normal [mem 0x00000000-0x1fffffff]
HighMem [mem 0x20000000-0x3fffffff]
Movable zone start for each node
Early memory node ranges
node 0: [mem 0x00000000-0x0fffefff]
node 0: [mem 0x30000000-0x3fffffff]
Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130047
Kernel command line: mem=0x0100M mem=0x0100M@0x30000000 root=/dev/loop0 root=/dev/mmcblk0p
1 rootfstype=vfat rootwait ro init=/sbin/init init=/mininit-syspart console=ttyS2,57600 co
nsole=tty0 fbcon=bind:0 rfkill.default_state=0 -- hwvariant=v20_mddr_512mb panic=5 conso
le=ttyS2,57600 console=tty0 boot=/dev/mmcblk0p1 loop0=/boot/rootfs.squashfs root=/dev/loop
0 rfkill.default_state=0
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 510024K/524284K available (4231K kernel code, 198K rwdata, 892K rodata, 300K init,
109K bss, 14260K reserved, 262144K highmem)
NR_IRQS:384
Console: colour dummy device 80x25
console [tty0] enabled, bootconsole disabled
console [ttyS2] enabled
Calibrating delay loop... 792.57 BogoMIPS (lpj=1585152)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
devtmpfs: initialized
pinctrl core: initialized pinctrl subsystem
regulator-dummy: no parameters
NET: Registered protocol family 16
JZ4770 GPIO initialized
PLL0 rate: 996000000
PLL1 rate: 432000000
GCW Zero JZ4770 setup
bio: create slab <bio-0> at 0
USB power: 3300 mV normal
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
i2c-gpio i2c-gpio.0: using pins 126 (SDA) and 127 (SCL)
i2c-gpio i2c-gpio.1: using pins 158 (SDA) and 159 (SCL)
i2c-gpio i2c-gpio.3: using pins 101 (SDA) and 100 (SCL)
i2c-gpio i2c-gpio.4: using pins 102 (SDA) and 103 (SCL)
Linux video capture interface: v2.00
Advanced Linux Sound Architecture Driver Initialized.
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Switched to clocksource jz_clocksource
NET: Registered protocol family 2
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
bounce pool size: 64 pages
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 484
io scheduler noop registered
io scheduler deadline registered (default)
jz-lcd jz-lcd.0: LCD disable timeout!
jz-lcd jz-lcd.0: fb0: jz-lcd frame buffer device, using 3600K of video memory
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
serial8250: ttyS2 at MMIO 0x0 (irq = 3, base_baud = 750000) is a 16550A
REG_CPM_GPUCDR= 0x00000001
GPU CLOCK USE PLL0
GPU GPU_CLK2x= 498 MHz
galcore options:
irqLine = 6
registerMemBase = 0x13040000
registerMemSize = 0x00040000
contiguousSize = 4194304
contiguousBase = 0x00000000
bankSize = 0x02000000
fastClear = -1
compression = -1
signal = 48
baseAddress = 0x00000000
physSize = 0x00000000
loop: module loaded
misc jz-vpu: Driver registered
jz4760: Normal mode.
musb-hdrc musb-hdrc.0.auto: USB OTG default mode: B
musb-hdrc musb-hdrc.0.auto: DMA IRQ: Shared. DMA Channels: 6.
jz4760: Disable USB PHY.
musb-hdrc musb-hdrc.0.auto: MUSB HDRC host driver
musb-hdrc musb-hdrc.0.auto: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
jz4760: Enable USB PHY.
using random self ethernet address
using random host ethernet address
usb0: HOST MAC fa:5f:a0:16:42:a4
usb0: MAC a6:3d:65:ec:a8:ff
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
jz4760: Enable USB PHY.
mousedev: PS/2 mouse device common for all mice
jz4770-touchscreen jz4770-touchscreen.2: Got platform irq: 84
input: analog joystick as /devices/platform/jz4770-adc/jz4770-touchscreen.2/input/input0
input: pwm-haptic as /devices/platform/input/input1
jz4740-rtc jz4770-rtc: rtc core: registered jz4770-rtc as rtc0
i2c /dev entries driver
radio-rda5807 0-0011: Found FM radio receiver
jz-msc jz-msc.0: JZ SD/MMC card driver registered
jz-msc jz-msc.1: JZ SD/MMC card driver registered
g_ether gadget: high-speed config #1: CDC Ethernet (ECM)
I2S: enter jz4770_snd_tx_ctrl, on = 0
I2S: enter jz4770_snd_rx_ctrl, on = 0
mmc0: host does not support reading read-only switch. assuming write-enable.
gcw0-audio gcw0-audio: jz4770-hifi <-> jz4770-i2s mapping ok
input: GCW0 Headphone Jack as /devices/platform/gcw0-audio/sound/card0/input2
mmc0: new high speed SD card at address e624
oprofile: using timer interrupt.
TCP: cubic registered
mmcblk0: mmc0:e624 SU02G 1.84 GiB
NET: Registered protocol family 17
rfkill-regulator rfkill-regulator.0: gcw0-wifi initialized
mmcblk0: p1 p2
input input0: Dropping handle 'js0' from handler 'joydev'
input input0: Dropping handle 'event0' from handler 'evdev'
linkdev linkdev: Connected to device analog joystick
linkdev linkdev: linkdev handler successfully registered
platform linkdev: Driver linkdev requests probe deferral
input: gpio-keys as /devices/platform/gpio-keys/input/input3
input input3: Dropping handle 'kbd' from handler 'kbd'
platform linkdev: Connected to device gpio-keys
linkdev linkdev: Axis 16 not found on device gpio-keys
linkdev linkdev: Axis 17 not found on device gpio-keys
jz4740-rtc jz4770-rtc: setting system clock to 1970-01-01 00:00:01 UTC (1)
ALSA device list:
#0: GCW0
input: linkdev device (Analog 2-axis 8-button 2-hat) as /devices/platform/linkdev/input/in
put4
Freeing unused kernel memory: 300K (80545000 - 80590000)
FAT-fs (loop0): invalid media value (0x00)
FAT-fs (loop0): Can't find a valid FAT filesystem
udevd[79]: starting version 1.5.3
udevd[79]: specified group 'dialout' unknown
udevd[79]: specified group 'kmem' unknown
udevd[79]: specified group 'video' unknown
udevd[79]: specified group 'lp' unknown
udevd[79]: specified group 'floppy' unknown
udevd[79]: specified group 'cdrom' unknown
udevd[79]: specified group 'tape' unknown
mxc6225 1-0015: I2C write failed: -6
mxc6225 1-0015: Write failed; assuming no device
EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
EXT4-fs (mmcblk0p2): recovery complete
EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
_________________________
< Welcome to OpenDingux ! >
-------------------------
\ ^__^
\ (oo)\_______
(__)\ )\/\
||----w |
|| ||
opendingux:/media/data/local/home #